To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10676 (+10)
  Re: Increasing current output to motors on HandyBoard
 
So that's like $28 for the H excluding the protecting circuitry? How much did this setup cost for both motors? ---...--- ericson mar Robotics Consultant mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the (...) (28 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Quick troubleshooting help please!!!!
 
I would also check the circuit traces. Clip an ohm meter to the battery ground and check all the ground points, then do the same for +battery. Take a magnifying glass to the traces you can see. Look for places where the smoke got out. Once the (...) (28 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Increasing current output to motors on HandyBoard
 
Total cost for both, $56.00. Smaller ones are cheaper. Again, the advantage is convenience, not cost. These pulg right into the motor driver output ports on either the Handy Board or the Rug Warrior with the L293D left in place, and take no other (...) (28 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
 
  multitasking
 
I have a simple question regarding multitasking. I am using two subroutine in a multitasking. start_process(ir()); start_process(detect()); Both subroutine should run for 5 ms(default). Consider an example that the subroutine detect() require more (...) (28 years ago, 11-Apr-99, to lugnet.robotics.handyboard)
 
  Non-Lego mechanics reference / New Ideas?
 
Hi all, Has anyone come across any good basic mechanical reference resources? I have found that patent searches are a tad more complex than what I am looking for. I would be interested in hearing about non-Lego reference sites (or books!!)that cover (...) (28 years ago, 11-Apr-99, to lugnet.robotics)
 
  Re: multitasking
 
(...) The subroutines continue execution exactly where they left off, making the multitasking transparent to you. You normally shouldn't have to give any thought to how many ms each one gets. If timing is important to you for some reason and the (...) (28 years ago, 11-Apr-99, to lugnet.robotics.handyboard)
 
  Non-Lego mechanics reference / New Ideas? (fwd)
 
----- Forwarded message from Kipling Morris ----- From: "Kipling Morris" <kiplingm@javanet.com> Subject: Non-Lego mechanics reference / New Ideas? Date: Sun, 11 Apr 1999 10:54:59 GMT Has anyone come across any good basic mechanical reference (...) (28 years ago, 11-Apr-99, to lugnet.robotics)
 
  Re: Increasing current output to motors on HandyBoard
 
Hi, Anyone know where I can purchase a commercial unit that I can operate automobile starter type relays from the COMOS outputs on the handyboard expansion board? only 5 mA per output. Or would it be eaiser to fabricate? I don't want to damage the (...) (28 years ago, 11-Apr-99, to lugnet.robotics.handyboard)
 
  part C3????
 
I need a reliable easy source to purchase part C3 online...digikey says it's obsolete and they have no substitute. Can anyone help??? -Jon (28 years ago, 11-Apr-99, to lugnet.robotics.handyboard)
 
  Smooth PWM for IC3.2?
 
Hi everybody, I have IC3.2 and want to use the smooth PWM functions. I've already adapted my lib_hb.c file. If I use the pcode_hb.s19 file adapted for smooth PWM (downloaded from Fred Martin's site), everything works ok, only I end up with IC2.8! (...) (28 years ago, 11-Apr-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR