To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10581 (+10)
  GCC: Status
 
It looks like at least three of us were playing with gcc-2.8.1 over the weekend. The GCC Miniboard library is now mostly ported over to the Handyboard, and the ICC11 LCD routines are almost done being ported over. I couldn't test out the motor (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
 
  Re: mailing list archive site
 
(...) This is a great idea, Jeff! From all of us, thanks. Duncan (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
 
  Quick troubleshooting help please!!!!
 
Hey, Two weeks before we present our project and the HandyBoard got fried!!! Ahhh! Oh well, hopefully someone can help us identify the problem. The board seems to work fine as long as its getting power through the RS-232 connection. Once this is (...) (28 years ago, 5-Apr-99, to lugnet.robotics.handyboard)
 
  Counting pulses
 
Could any one point me in the right direction for information on calculating frequency using the handyboard, Thanks Keith (28 years ago, 6-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Quick troubleshooting help please!!!!
 
Did you destroy the battery pack? There is an embedded temperature fuse that will blow if you try to charge it too fast or accidently short the battery. With no power applied have a look at the voltage on the battery terminals (you can get to them (...) (28 years ago, 6-Apr-99, to lugnet.robotics.handyboard)
 
  HB encoders question
 
Can the HB measure encoder pulses faster than 1 kHz? (this is the speed of the system interrupt) Assume we have an encoder that does 500 pulses per revolution. What happens when we exceed 2 revolutions per second? What happens if the encoder has two (...) (28 years ago, 6-Apr-99, to lugnet.robotics.handyboard)
 
  Re: gcc build instructions for linux
 
(...) Has anyone successfully built the above target using egcs-1.1.2? My attempt failed in libiberty: ... configure: error: installation or configuration problem: C compiler cannot create executables. make: *** [configure-target-libiberty] Error 1 (...) (28 years ago, 6-Apr-99, to lugnet.robotics.rcx.legos)
 
  RE: Looking for Step-by-Step Instruction
 
Jonathan Knudsen is writing an O'Reilly book, details at (URL) . Asides from that, check the mindstorms website frequently... # -----Original Message----- # From: jeff@learningstar.com # Sent: 02 April 1999 19:19 # To: lego-robotics@crynwr.com # (...) (28 years ago, 6-Apr-99, to lugnet.robotics)
 
  RE: Walker
 
do you have to email html? It's rather irritating. # -----Original Message----- # From: Robot2n@aol.com # Sent: 03 April 1999 21:39 # To: lego-robotics@crynwr.com # Subject: Walker # # # ---...--- # ---...--- # [Unable to display image]Hi everyone, (...) (28 years ago, 6-Apr-99, to lugnet.robotics)
 
  Re: gcc build instructions for linux
 
I have. I got the same message. I assume it is part of the test suite. I just bit the bullet and did a "make install" anyway, and it works fine. I take it as saying that it cannot generate an executable for the host platform, which would be true, (...) (28 years ago, 6-Apr-99, to lugnet.robotics.rcx.legos)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR