To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10406 (+10)
  Re: Why do it? Was: multi-device output controller
 
My original message described the controller with two inputs, one for device selection and one for device power. This could easily be connected to whatever power source the user desires. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  RE: Muscle wire and alternatives
 
I have connected nitinol to Lego and it can melt the ABS plastic...be careful. Rich (URL) Message----- From: Jim Choate [mailto:ravage@EINST...N.ssz.com] Sent: Friday, March 26, 1999 11:36 AM To: lego-robotics@crynwr.com Subject: Muscle wire and (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  RE: Why do it? Was: multi-device output controller
 
(...) Measuring PWM is not difficult, but it would involve a micro (PIC12C508 anyone?) dedicated to the task and then you would have to get it to drive the RCX, which means motor drivers, etc. If you are willing to spend $50 and LOTS of time, then (...) (28 years ago, 27-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
 
  Why do it? Was: multi-device output controller (fwd)
 
----- Forwarded message from Ralph Hempel ----- From: "Ralph Hempel" <rhempel@bmts.com> Subject: Why do it? Was: multi-device output controller Date: Fri, 26 Mar 1999 22:17:57 GMT With all of the talk about RS232 converters, and PWM decoders, why (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
 
  Re: LEGO 9V battery box as project container
 
(...) Can anyone guess how long a 9 volt battery power supply like this will last compared to 6 AA batteries? This does seem like a good small power solution and project box. <ICS> -- Did you check the web site first?: (URL) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  RE: Why do it? Was: multi-device output controller (fwd)
 
(...) Hmmm, the RCX tower is a pretty effective RS232 converter...and you will still need to write special software for the RS232 convertor's interface to the PC. Like I said, its cheaper and quicker to buy a second RCX from Pitsco... Cheers, Ralph (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
 
  RE: Why do it? Was: multi-device output controller (fwd)
 
----- Forwarded message from Ralph Hempel ----- Subject: RE: Why do it? Was: multi-device output controller (fwd) Date: Sat, 27 Mar 1999 02:17:09 GMT (...) Hmmm, the RCX tower is a pretty effective RS232 converter...and you will still need to write (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
 
  Re: Polarity Switch = Pressure Switch
 
(...) Good job, Ralph! The most compact solution seen up to now for a pneumatic switch. Mario (28 years ago, 27-Mar-99, to lugnet.build, lugnet.robotics)
 
  analog inputs on expansion board
 
Hi, Two questions: 1) When I plug a Lego reflectance sensor into the expansion board it seems to work fine. When I use the angle sensor it seems to work fine. When I plug them in at the same time the angle sensor stops working. No change to the (...) (28 years ago, 27-Mar-99, to lugnet.robotics.handyboard)
 
  Handy Board inputs
 
Hi, my name is Becky Browning. I am currently working on building a robot using the Handy Board. I am having considerable troubles though getting either the digital or analog inputs to work. Right now I have analogs ports 0 and 1 working with (...) (28 years ago, 27-Mar-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR