 | | Re: [Fwd: Robot Mapping]
|
|
-->Heck, that sounds pretty easy. As long as you know where you start from and you use a cartesian or -->polar form of V=vsub0 + a*t integrated over time, and you are either working in a vacuum or at such low -->velocities that c sub d is (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
(...) As for the diode vs FET, the package used for surface mount is going to be the same so there is no size penalty. The only thing I might change is the regulator, on battery powered equipment I would tend to a DC to DC converter like Motorola's (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
What about a real time circuit that routed the output power to one of eight output ports depending on the PWM. That way it only takes one output port on the RCX and up to three (out of 24) motors could be running at the same time. (...) like (...) (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
----- Forwarded message from Joel Shafer ----- Date: Thu, 25 Mar 1999 13:43:33 -0600 From: Joel Shafer <joel@connect.net> Subject: Re: multi-device output controller What about a real time circuit that routed the output power to one of eight output (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: 3-wire converter for homebrew sensors (fwd)
|
|
----- Forwarded message from Pete Sevcik ----- Date: Thu, 25 Mar 1999 21:00:13 -0600 From: Pete Sevcik <sevcik@flash.net> Subject: Re: 3-wire converter for homebrew sensors The angle sensor connected straight to the RCX is non-linear because it is (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | FIRST™ LEGO® League
|
|
Found a link to this... (URL) the official LEGO MINDSTORMS website -- specifically, this page: (URL) (28 years ago, 26-Mar-99, to lugnet.robotics.events)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
How well does this work? Contrast with: (URL) on (URL) I got from lu, and which seems to require a fair bit of fiddling to get it to regulate correctly. (...) (28 years ago, 26-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: HB Memory
|
|
Thanks everybody. (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | gcc build instructions for linux
|
|
Linux Tools for Hitachi H8/300 Microprocessor Development (URL) came across this site today. It has good instructions for building the gcc h3000 compiler on Linux. I thought people here might also be interested in the crt0.s 'C' startup source. I (...) (28 years ago, 26-Mar-99, to lugnet.robotics.rcx.legos)
|
| |
 | | RE: Polarity Switch = Pressure Switch
|
|
(...) Mine required no tuning at all, if that's what you mean. I tried a similar configuration to lu's and found that the throw was difficult to get right. I don't like the overall size of my regulator, but it works like a champ! Cheers, Ralph (...) (28 years ago, 26-Mar-99, to lugnet.build, lugnet.robotics)
|