 | | RE: Robot Mapping
|
|
Check this reference out: "Autonomous Agent Map Construction in Unknown Enclosed Environments", Keith L. Doty and Steven L. Seed, Machine Intelligence Lab, DEE, University of Florida, Gainesville, FL and Chapter 10 of: "Sensors for Mobile Robots, (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Robot Mapping
|
|
(...) I've been thinking about this too. The problem as I see it is that without some shaft encoders on the wheels, your robot doesn't really know how far it's moved, and therefore where it is in the map. If you power on the forward motor for 2 (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | [Fwd: Robot Mapping]
|
|
-- ___...___ Jonathan Pennington -Anthropologist/Geologist -Linux User and Advocate -Bart Simpson Sympathizer Email at jwp(at)awod.com ___...___ (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: [Fwd: Robot Mapping]
|
|
(...) Heck, that sounds pretty easy. As long as you know where you start from and you use a cartesian or polar form of V=vsub0 + a*t integrated over time, and you are either working in a vacuum or at such low velocities that c sub d is negligible, (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
Dennis, Thanks for your encouragement. The angle sensor connected straight to the RCX is non-linear because it is in series with another resistor located inside the RCX. During a sense operation, the RCX drives the sensor input from a 10K resistor (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: [Fwd: Robot Mapping]
|
|
-->Heck, that sounds pretty easy. As long as you know where you start from and you use a cartesian or -->polar form of V=vsub0 + a*t integrated over time, and you are either working in a vacuum or at such low -->velocities that c sub d is (...) (28 years ago, 26-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
(...) As for the diode vs FET, the package used for surface mount is going to be the same so there is no size penalty. The only thing I might change is the regulator, on battery powered equipment I would tend to a DC to DC converter like Motorola's (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
What about a real time circuit that routed the output power to one of eight output ports depending on the PWM. That way it only takes one output port on the RCX and up to three (out of 24) motors could be running at the same time. (...) like (...) (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
----- Forwarded message from Joel Shafer ----- Date: Thu, 25 Mar 1999 13:43:33 -0600 From: Joel Shafer <joel@connect.net> Subject: Re: multi-device output controller What about a real time circuit that routed the output power to one of eight output (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: 3-wire converter for homebrew sensors (fwd)
|
|
----- Forwarded message from Pete Sevcik ----- Date: Thu, 25 Mar 1999 21:00:13 -0600 From: Pete Sevcik <sevcik@flash.net> Subject: Re: 3-wire converter for homebrew sensors The angle sensor connected straight to the RCX is non-linear because it is (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|