To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10186 (+20)
  [meta] mailing list & newsgroup
 
(...) Rob, There is a mailing list (lego-robotics@crynwr.com) which is gatewayed with the lugnet.robotics newsgroup. Anything you post to lugnet.robotics shows up on the mailing list, and vice-versa*. The lego-robotics mailing list has a (...) (28 years ago, 15-Mar-99, to lugnet.robotics, lugnet.admin.general)
 
  Re: Good source for Lego Technic parts?
 
Certain items, most notably motors, are *significantly* cheaper than Pitsco if you order them through the LEGO shop-at-home catalog (1-800-453-4652). If you are ordering for an educational instititution and if you ask the shop-at-home people, you (...) (28 years ago, 15-Mar-99, to lugnet.robotics.handyboard)
 
  NQC known bug
 
Just wanted to inform everyone of a nastly little NQC bug in version 1.2: return statements in inline functions actually cause a top-level return from the enclosing subroutine / task. For example in the following code, sound 1 is never played: (...) (28 years ago, 15-Mar-99, to lugnet.robotics.rcx.nqc)
 
  New pbFORTH release
 
This is an announcement of the latest version (102) of pbFORTH available at: (URL) This release of pbFORTH addresses some errors in the previous version including a fairly serious stack problem in TIMER_SET. Also POWER_OFF now works as advertised, (...) (28 years ago, 15-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
 
  Re: Source for Sharp GP1U581Y ???
 
Thanks to all for your responses ... but I still haven't been able to locate a supplier for the GP1U581Y IR detector. A search of B.G.Micro's and DigiKey's web sites produced no results. The two local Radio Shacks stock a similar unit by Everlight, (...) (28 years ago, 15-Mar-99, to lugnet.robotics)
 
  Help me, simulator
 
Hello Apreciate group of handy board Anyone can help me to recomend me some free very good simulator of the 68HC11 microcontroller, I apreciate very much your help, also the internet address where I can obtain it. with my best regards Carlos J. (...) (28 years ago, 15-Mar-99, to lugnet.robotics.handyboard)
 
  Re: Source for Sharp GP1U581Y ???
 
In article <36EC9BE8.8005AAC4@iname.com>, Nick Taylor <ntaylor@iname.com> writes (...) Did you read the response which suggested you had copied a typo, and that the part number should be GP1U58Y? (28 years ago, 15-Mar-99, to lugnet.robotics)
 
  Re: Shaft-Encoders
 
Hi, It's very interesting to use mouse QUADRIC encoders for HB as shaft encoders? If anybody make this in hardware? If so, may you give a links? ===...=== -----Original Message----- From: Max Davies <mdavies@CAM.ORG> (...) (28 years ago, 15-Mar-99, to lugnet.robotics.handyboard)
 
  wireless connection
 
-- MIME ATTACHMENTS DISCARDED: 1. Content-Type: text/plain; charset="euc-kr" Content-Transfer-Encoding: base64 Content-Length: 492 2. Content-Type: text/html; charset="euc-kr" Content-Transfer-Encoding: base64 Content-Length: 1412 (28 years ago, 15-Mar-99, to lugnet.robotics.handyboard)
 
  wireless connection
 
-- MIME ATTACHMENTS DISCARDED: 1. Content-Type: text/plain; charset="euc-kr" Content-Transfer-Encoding: base64 Content-Length: 496 2. Content-Type: text/html; charset="euc-kr" Content-Transfer-Encoding: base64 Content-Length: 1428 (28 years ago, 15-Mar-99, to lugnet.robotics.handyboard)
 
  H8300 Stack and SLEEP
 
Hi All, If this is old news, ignore it... I just figured out this weekend (thanks Kekoa) that the H8/300 stack pointer (r7) and the power-down function in the RCX have a close relationship. The stack pointer MUST be in the on-chip RAM area (0xFD80 (...) (28 years ago, 15-Mar-99, to lugnet.robotics.rcx.legos, lugnet.robotics.rcx.pbforth, lugnet.robotics)
 
  Robot intelligence
 
In the book "How to design and build your own custom robot" by David L. Heiserman, Tab Books, I found a classification of robots according to their "intelligence" (pages from 11 to 17). I wonder if this is just the author's thought or if there's a (...) (28 years ago, 15-Mar-99, to lugnet.robotics)
 
  0.1 MF capacitor"104" help
 
How do you tell what is the negative on the cap labelled "104" both sides look the same. please help does the label go in towards the max232 or out towards the edge? ___...___ Steve Wall Sir Sandford Fleming college Swall@flemingc.on.ca (28 years ago, 15-Mar-99, to lugnet.robotics.handyboard)
 
  Re: Source for Sharp GP1U581Y ???
 
(...) Digikey: part number 160-1060-ND on page 575 BG Micro: part number LED1001 on page 2 Radio Shack: part works fine, just solder leads on at right angles (use cut-off ends of resistors or what-not) just make sure you observe proper pinout. (...) (28 years ago, 15-Mar-99, to lugnet.robotics)
 
  FW: H8300 Stack and SLEEP
 
(...) Markus, (and anyone else listening) I think it applies to the RCX power_shutdown() function as described in Kekoa's reference. The key is that this function puts the external RAM into low-power mode. If you are not calling power_shutdown() or (...) (28 years ago, 15-Mar-99, to lugnet.robotics.rcx.legos, lugnet.robotics, lugnet.robotics.rcx.pbforth)
 
  Re: 0.1 MF capacitor"104" help
 
(...) Normally capacitors with values less than 1uF will not have a polarity. They can go in either way. (...) Doesn't matter. I try to make all the labels face the same way when I build a board. It makes things look better, but it is only for (...) (28 years ago, 15-Mar-99, to lugnet.robotics.handyboard)
 
  Re: Ultimate Starter Sets / Add-Ons for Mindstorm? Reprise
 
Lewis, James C. wrote in message <000e01be6c1f$493be2...th.net>... (...) LEGO ZNAP is 'perfect' for building large robots. It's relatively light, suited for large structures, and it's very easy to build with by inexperienced builders. Technic (...) (28 years ago, 15-Mar-99, to lugnet.robotics)
 
  Program Wanted
 
Does anyone have a program for the Recycler robot? Please help! Adamski _______ <adamski2000@adamski...rve.co.uk> (28 years ago, 15-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.legos)
 
  INTERACTIVE C AND THE .ICB COMPILER
 
Hello, My problem lies with the downloading of a constructed .icb file created for the .icb compiler from Newton Labs. I have written a .asm file and compiled it using the web page (URL) The code compiles successfully and when I copy the associated (...) (28 years ago, 15-Mar-99, to lugnet.robotics.handyboard)
 
  Are E9's compatible with HB?
 
I have a line on a bunch of MC68HC11E9's and I was wondering if these were compatible with the HB. Any help would be great! STEVE ___...___ Steve Wall Sir Sandford Fleming college Swall@flemingc.on.ca (28 years ago, 15-Mar-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR