To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10116 (+10)
  Re: DC motor with encoders
 
Hi ever heard of Maxon Motors (the one that supplied the Pathfinder on Mars with motors). They have hi quality low voltage motors. We are using them here. They have opticel encoders (HP) directly mounted. Price arouonf $120 for a 15W motor incl. (...) (28 years ago, 11-Mar-99, to lugnet.robotics.handyboard)
 
  Re: Idle process
 
(...) I, too, consider power saving to be a valuable (indispensible) feature. That is precisely the sort of thing that I feared I might be overlooking. Up 'till now, I had not worked on an embedded project which would benefit from using (...) (28 years ago, 9-Mar-99, to lugnet.robotics.rcx.legos)
 
  RE: DC motor with encoders
 
Thanks for the tip. Lotsa cool goodies. shan o (...) (28 years ago, 11-Mar-99, to lugnet.robotics.handyboard)
 
  Re: Idle process
 
Sorry this message is so late, I had to get registered for posting from my work address. (...) I, too, consider power saving to be a valuable (indispensible) feature. That is precisely the sort of thing that I feared I might be overlooking. Up 'till (...) (28 years ago, 11-Mar-99, to lugnet.robotics.rcx.legos)
 
  Re: Sensors
 
Hi We just built a IR detection with a Radio Shack IR LED and their Sharp detector GD1U..whatever....cost a few dollars. Basically detects anything within about 60 cm, depending on what surface you are reflecting off of. We found that we had to (...) (28 years ago, 11-Mar-99, to lugnet.robotics.handyboard)
 
  Re: Idle process
 
(...) The idle task actually has the lowest priority in my scheme, but there was some efficiency gained in making the task list loop around. If the idle task is always there, it makes for simplified code in multitasking startup if you rely on that. (...) (28 years ago, 11-Mar-99, to lugnet.robotics.rcx.legos)
 
  Re: programming???
 
(...) I use the RCX Command Center and NQC to program. RCXCC is a very nice environment for writing, debugging, downloading, and calibrating values. You can directly control the brick from the PC, directly look at all of the sensor values, poll (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Sensor readings on the RCX display
 
I know that you old-timers (?-) out there already know this, but I just learned it last week and some others may not know by now. You can read the sensor values directly on the brick's display by pressing the "view" button repeatedly until the (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Where do I get Spirit.ocx?
 
Please Help!!! Adamski _______ <adamski2000@adamski...rve.co.uk> (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Re: Get 8 Outputs from RCX: A Pure-Lego Solution
 
(...) But then we run out of outputs for the controlling motors. On the other hand, we may layer four stages of the 4-way splitter into a 256- way, then use both directions of the other two outputs to control these four stages... I think this is (...) (28 years ago, 11-Mar-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR