 | | crystals and voltage monitors
|
|
Hi. Does anyone have current part numbers/vendors for the 8MHZ crystal and the U12 Voltage Monitor on the Handy Board? Are the correct values available from digi-key? I saw they carry both crystals and voltage monitors, I just don't want to order (...) (28 years ago, 10-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Air Tank overload??
|
|
(...) There are many compressor on the web. You can see my version on my web site (Lego/Mindstorm section, S5 creature). I used an idea from Bert Van Dam's page to stop the compressor when pressure is enough. (Bert's address on my page too). Mario (...) (28 years ago, 10-Mar-99, to lugnet.robotics)
|
| |
 | | Re: pneumatic tubing
|
|
I found that the neoprene tubing used as fuel lines for R/C airplanes works pretty well and is cheaper than S@H. You should be able to find some at a good hobby store. Dave (...) (28 years ago, 10-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Cybermaster memory limit?
|
|
(...) I always managed to run into it in my first projects. :-( Since I decided to transfer the real "intelligence" of the bot to the PC, leaving only basic intelligence in the mobile unit, the problems finished... but not only after some struggle. (...) (28 years ago, 9-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Vision on the Handy Board?
|
|
I hade the same idea, with a parallel port camera, just to see what can happen. If I'm not wrong it is possible to use a parallel port -> RS232 interface. Am I wrong ? Stefano Falconetti ---...--- (...) recognition? (...) any (...) (28 years ago, 10-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Vision on the Handy Board?
|
|
Hi Bill we are using a NewtonLabs cognachrome system on one of our model cars. The car is equiped with a Handyboard, a cognachrom system, a camera, and a couple of RS232 to CAN converters. Our Handyboard has a CAN controller attached to it for (...) (28 years ago, 10-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Vision on the Handy Board?
|
|
Excuse me what is it a CAN controller ? Stefano ---...--- (...) a (...) communication. (...) to (...) transmitted (...) system. But (...) slow. (...) serial (...) framegrabber) (...) Maybe (...) the (...) useful (...) Some (...) be (...) (...) (28 years ago, 10-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Memory peripheral device
|
|
I,m trying to give to my 68hc11 board a memory mass storage device, like a floppy reader, or a disk, or a disk on chip, or a PCMCIA memory card interface, I found a way but I'd like to know if someone of you did something like this before me. Thanks (...) (28 years ago, 10-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Memory peripheral device
|
|
I,m trying to give to my 68hc11 board a memory mass storage device, like a floppy reader, or a disk, or a disk on chip, or a PCMCIA memory card interface, I found a way but I'd like to know if someone of you did something like this before me. Thanks (...) (28 years ago, 10-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Vision on the Handy Board?
|
|
CAN = Controler Area Network (...) -- Thomas Hauri ZHW Zuercher Hochschule Winterthur University of applied sciences Technikumstr.9 /PF CH-8401 Winterthur Switzerland Phone : +41 52 267 74 79 Fax : +41 52 268 74 79 Mail : har@zhwin.ch HP : (URL) (28 years ago, 10-Mar-99, to lugnet.robotics.handyboard)
|