To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1001 (+20)
  Re: mode select pins
 
(...) The HB runs in special test mode to facilitate control of the LCD screen. Read the Appendix B information in the Tech Docs section for more info. -Fred (30 years ago, 19-Nov-96, to lugnet.robotics.handyboard)
 
  Polaroid Sonar
 
Hi, I'm powering my Ranging Module with the 9.6V unregulated motor power header. Does anyone know if there is a danger in doing so? (30 years ago, 19-Nov-96, to lugnet.robotics.handyboard)
 
  Battery Care
 
Hi, What's the best way to care for the NiCd pack of the Handyboard? I understand that NiCd's undergo the "memory effect". Does this mean that you should always use your Handyboard untill the RED LED light comes on...and then recharge it? Is it OK (...) (30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  IR communication (fwd)
 
Can someone please attempt to help me out.. second posting??? I want to get five handyboards to talk to each other using infrared transmission... I use infrared transmitter/receiver reflectance sensors for other things... 1) What parts (I need (...) (30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  Re: Polaroid Sonar
 
Yeah, mine too! :D But, it works! btw, what kind of message was that? (...) (30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  RE: IR communication (fwd)
 
There will be a lot of IR radiation bouncing around and that can be problematic. Another IR detection technique is to use a camcorder, they are sensitive to IR light. Low light CCD cameras are even better. If you want to hook up 4 IR xmitters from a (...) (30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  Integer -> float
 
I know I have seen the answer to this somewhere before, but I can't remember how to convert an integer to a float. Micah D. Krider kmicah@uwf-uf.ee.uwf.edu (30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  Re: Integer -> float
 
Hi Micah, To convert an int to a float, simply type: i=(float)f; where i is the integer and f is a float. - Prabal (...) (30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  Digitals outputs and SPI
 
Hi, I read something about controlling the SPI bus and about adding digital outputs, but I can't find it anymore. Can anybody help me? Thanks. Regards. -David (30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  Re: Digitals outputs and SPI
 
(...) Go to the FAQ. -Fred (30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  Re: Integer -> float
 
(...) Are you sure about this? In your example, i is the float and f the integer. Silvain (30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  Re: Integer -> float
 
Oops! That should be: f=(float)i; That's what happens when you stay up too late. :-) - Prabal (...) (30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  RE: sonar (fwd)
 
(30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  Polaroid Sonar Conector
 
Does anyone know where to get a connector that will mate the one provided by Polaroid for the 6500 Ranging Module.? (30 years ago, 20-Nov-96, to lugnet.robotics.handyboard)
 
  HandyBoard Expansion.....
 
Hi I'm roughing out a design to add some more(*) IO to my handyboard and have run into a slight problem.... I'm going to have another 4 devices on the data bus, 2 x 74HC574 & 2 x 74HC541. Will this exceed the "fan out" of the cpu ? (I don't have the (...) (30 years ago, 21-Nov-96, to lugnet.robotics.handyboard)
 
  Interface/charge board problem>>part II :)
 
Hello again, After several fustrating hours of checking all solder connections, cables, and all that other stuff. I finaly think that my problem is in the MAX232 chip on the charger board. If I remove the chip from it's socket, the handy board will (...) (30 years ago, 21-Nov-96, to lugnet.robotics.handyboard)
 
  bus loading
 
Hi Scott, (...) Since everything's CMOS, there's no trouble with static loading (CMOS inputs require essentially zero current in static operation). You will, however, be increasing the capacitance on the bus, which slows down the transitions a (...) (30 years ago, 21-Nov-96, to lugnet.robotics.handyboard)
 
  Polaroid & Handyboard
 
Okay...I hooked up a Polaroid Rannging board to the Handyboard. And something about the supply prevents the echo from being properly detected. If I provide power from a more substantial supply, the echo is detected correctly (I was watching this on (...) (30 years ago, 21-Nov-96, to lugnet.robotics.handyboard)
 
  Voltage regulator gets hot when steering servo
 
Hi, I'm working on a project in which I use the handy-board to steer a servo. I noticed that the voltage regulator on my handy-board gets rather hot. You actually burn your fingers on it... So I wondered how much current I can draw from it, without (...) (30 years ago, 21-Nov-96, to lugnet.robotics.handyboard)
 
  (no subject)
 
Can somebody help me? I had like to use the SPI of the 68HC11, did anybody already do this? Thanks. (30 years ago, 21-Nov-96, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR