 | | Yellow/white color change?
|
|
I received a Bricklink parts order recently containing some white and yellow pieces that look slightly different from the colors I'm used to. The colors on these parts are a bit less saturated than those of my existing pieces. The difference is (...) (18 years ago, 7-Jun-07, to lugnet.parts)
|
| |
| | Re: A few ways to use old skeleton arms!
|
|
(...) Indeed, the fit in the 1x1's is loose (my guess is it varies by arm), but the fit in the Technic cylinder is nice and tight! Dave S. (18 years ago, 16-May-07, to lugnet.parts, lugnet.general, FTX)
|
| |
| | Re: A few ways to use old skeleton arms!
|
|
(...) I've had arms slip into the 1x1s before, but they seemed rather loose. Do they hold inside the pin connector any better? Jeff (18 years ago, 14-May-07, to lugnet.parts, lugnet.general, FTX)
|
| |
| | A few ways to use old skeleton arms!
|
|
Hey all, While building my ZombieTron, I discovered these two fits for loose old skeleton arms. (URL) Dave S. (18 years ago, 13-May-07, to lugnet.parts, lugnet.general, FTX)
|
| |
| | Re: lego pick a brick
|
|
(...) Thanks Tim, what is in store PAB? Is that the Lego stores? I had one close by when I lived in Burbank and they sold them by the container. The large one was $16.00 and you could get a lot of bricks in them. I found a tun of yellow and tan 1x1 (...) (18 years ago, 7-May-07, to lugnet.parts)
|
| |
| | Re: lego pick a brick
|
|
(...) Practically everything is cheaper on BrickLink. Very few parts are cheaper from online Pick-a-Brick and shipping just makes it worse. Now, in-store PAB is a different deal. That can be incredibly cheap, for some parts. Tim (18 years ago, 6-May-07, to lugnet.parts)
|
| |
| | lego pick a brick
|
|
Who might know? I was just on Lego's pick a brick and a brick 1x1 that has the studs on two sides is 9 cents, studs on 4 sides is 24 cents, almost 3 times as much for 2 extra studs. (actually 3 studs for the first one and 5 for the second one.) I (...) (18 years ago, 5-May-07, to lugnet.parts)
|
| |
| | Re: If you could wish for any single Lego element, what would it be?
|
|
(...) snip I have thought of this off-and-on over the time since I've read this: Make all the arches as half-arches, like the 1x5x4 arch. That would eliminate the stress point problem. Larger arches, too, like 12-stud+ spans. Also in round (...) (18 years ago, 28-Apr-07, to lugnet.parts, FTX)
|
| |
| | Re: Which glue?
|
|
(...) Epoxy works like wood glue, in that it needs to permeate the surface of the materials that it is bonding in order to get anything more than a light adhesion. At my last job, when we were epoxying resin tooling board together, we'd regularly (...) (18 years ago, 6-Apr-07, to lugnet.parts.mod)
|
| |
| | Re: Which glue?
|
|
(...) Some of the thin CA glues have a solvent added (MEK?), the superglue brand seems to have more then the others. While working on some movie props I needed to glue some detail onto a curved surface. the thin SG brand caused the thin styrene (...) (18 years ago, 5-Apr-07, to lugnet.parts.mod)
|
| |
| | Re: Which glue?
|
|
(...) I've found cyanoacrylate 'Super Glue' isn't good at holding LEGO together for long. But, this is mainly down to the shiny surface of parts. Where I've sanded the edge of a push switch and fitted it into a train controller, it's an incredibly (...) (18 years ago, 5-Apr-07, to lugnet.parts.mod)
|
| |
| | Re: round brick 1x1 transgreen with solid stud
|
|
(...) I put the granular trees in the sets thinking people just wanted to keep those. I was wondering if any ever came with the tree or the sellers just were not willing to give them up. I know that the granular trees came an went very quickly, they (...) (18 years ago, 4-Apr-07, to lugnet.parts)
|
| |
| | Re: round brick 1x1 transgreen with solid stud
|
|
In lugnet.parts, John Patterson wrote: <SNIP> (...) John, many of the LEGO sets of the first half of the 1970's had those granular trees until 1974, when the models switched to conical Pine trees. You just happen to have later versions of those (...) (18 years ago, 4-Apr-07, to lugnet.parts)
|
| |
| | Re: round brick 1x1 transgreen with solid stud
|
|
(...) Like I said, post over there if you are looking for a part. Lots of times somebody will have one that they will list specially for you. Tim (18 years ago, 4-Apr-07, to lugnet.parts)
|
| |
| | Re: Which glue?
|
|
(...) As Aaron States, the use of MEK was BANNED from the Lego modelshops back in 1998, and GBL was introduced. Many health issues were being presented and an article written in the LEGO REVIEW magazine, a corporate magazine spoke about the (...) (18 years ago, 4-Apr-07, to lugnet.parts.mod, FTX)
|
| |
| | Re: round brick 1x1 transgreen with solid stud
|
|
(...) Thank you, thank you, thank you. I bought them both. They got to be rare at this point.I still wonder if they were put into sets. There is a granular tree on one of the houses, in the 350 range and I have several and none came with the tree on (...) (18 years ago, 4-Apr-07, to lugnet.parts)
|
| |
| | Re: round brick 1x1 transgreen with solid stud
|
|
(...) There are currently two for sale on BrickLink: (URL) is a different site with different search methods. Easy once you get it, but it can be a bit baffling at first. Post there or here if you need help with it. Tim (18 years ago, 3-Apr-07, to lugnet.parts)
|
| |
| | Re: round brick 1x1 transgreen with solid stud
|
|
(...) Thanks Bryan: I have not found any on bricklink and have looked and looked. If you see one someday let me know. Thanks again John P (18 years ago, 3-Apr-07, to lugnet.parts)
|
| |
| | Re: round brick 1x1 transgreen with solid stud
|
|
(...) There are sellers who are selling or have sold the part in question on Bricklink: (URL) I assume this piece exists. -Bryan (18 years ago, 3-Apr-07, to lugnet.parts)
|
| |
| | round brick 1x1 transgreen with solid stud
|
|
round brick 1x1 transgreen with solid stud: has anyone ever seen one? I have found it listed in several instructions but every set that it listed has the hollow stud. I am wondering if they ever made it, or it was introduced when the hollow stud (...) (18 years ago, 3-Apr-07, to lugnet.parts)
|
