Subject:
|
Re: I'm going to The Wedding!!!
|
Newsgroups:
|
lugnet.org.au, lugnet.loc.au
|
Date:
|
Thu, 29 Mar 2001 04:21:36 GMT
|
Viewed:
|
2576 times
|
| |
|
|
In lugnet.loc.au, Jonathan Wilson writes:
>
>
> Jonathan Wilson wrote:
>
> > Ross Crawford wrote:
> >
> > > In lugnet.org.au, Dave Low writes:
> > > >
> > > > Similar idea without the tokens--I spotted some happy little vegemite filled
> > > > tumblers (like the nutella ones) the other day. There must be Vegemite • teatowels
> > > > and so forth readily avialable at gift shops.
> > >
> > > I'll check it out!
> > >
> > > > I'm still keen on the MOC idea,
> > > > but I don't have enough curved pieces for a stubby holder I'm afraid...
> > > >
> > > > Maybe we could give the Todd and Suz minifigs all the gear they need for a • LegOz
> > > > honeymoon (someone builds the ute, someone builds the barbie, someone builds • the
> > > > dodgy Gold Coast hotel, someone builds the tiny Sydney Opera House and Uluru • to
> > > > use as backgrounds for their happy snaps).
> > >
> > > A MOC would be nice, but it'd have to be done fairly quickly - I'm leaving on
> > > April 24. Any takers?
> > >
> > > ROSCO
> >
> > I have a realy great minifig scale UTE design I did in ldraw.
> > Unfortunatly I dont have the pieces and getting them would probobly be hard
> > (and/or expensive) If there is anyone who has lots of older type town car pieces
> > (like car doors) that wants the design, let me know. I have done it in red but
> > any color would work.
>
> ok, here are the parts required to make this ute: (main refers to the main color of
> the ute)
> 2 main 2 x 2 tile with wheel holder pins
> 4 main wheel hubs to suit
> 4 black tyres to suit hubs
> 1 main 2 x 4 plate mudguard with studs
> 1 main slope 3 x 4 mudguard
> 2 trans clear 1 x 1 plate
> 1 main 1 x 2 plate
> 1 main 2 x 12 plate
> 2 main 4 x 2 plate
> 3 main 2 x 2 plate
> 1 main 2 x 4 plate
> 2 main 1 x 1 plate
> 2 tr red 1 x 1 plate
> 2 main 1 x 4 brick
> 1 main pair car doors 1 x 3
> 1 main car steering wheel
> 1 main car roof holder piece (1 x 4 x 2 with sticking up hinge)
> 1 main car roof (4 x 4)
> 1 tr clear winscreen (1 x 4 on top, 2 x 4 on bottom)
> 1 1 x 4 x 2 rollbar
>
> for the tray edges I used (there might be other solutions)
> 5 main 1 x 2 x 1 thinwall
> 2 main 1 x 1 x 1 corner thinwall (I dont know how hard these are to come by)
>
> If anyone has the parts to make this let me know and I will make up some
> instructions.
I can give this a burl -- probably don't need the instructions. Where do you fit
the roll-bar? Do people think that a traditional 4-wide car is okay, or would a
6 or 8 wide be better? I'm leaning toward the 8-wide option myself -- they can
always pretend it's a Yank pick-up if there are any concerns about scale.
--Dave
|
|
Message has 2 Replies:
 | | Re: I'm going to The Wedding!!!
|
| (...) fit (...) a (...) The more the better! Makes it more of an Aussie Gift (tm). It'd be nice if two minifigs could fit side-by-side. Although I s'pose they could be just standing beside it. Anyone got bride+groom minifigs? ROSCO (23 years ago, 29-Mar-01, to lugnet.org.au, lugnet.loc.au)
|
Message is in Reply To:
| | Re: I'm going to The Wedding!!!
|
| (...) ok, here are the parts required to make this ute: (main refers to the main color of the ute) 2 main 2 x 2 tile with wheel holder pins 4 main wheel hubs to suit 4 black tyres to suit hubs 1 main 2 x 4 plate mudguard with studs 1 main slope 3 x (...) (23 years ago, 29-Mar-01, to lugnet.org.au, lugnet.loc.au)
|
24 Messages in This Thread:
 
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
