 | | SCLF: Pasting tables &c. —Huw Millington
|
| | | Just catching up after being offline for a week... looks like it's been a busy one. Are we all set to bring our pasting tables for the layout? I'll be bringing about 25 MOC wagons, my greed diesel, my wagon repair shop if it'll fit in the car, my (...) (24 years ago, 22-Apr-01, to lugnet.loc.uk)
|
| | | |
| | | | | Re: SCLF: Pasting tables &c. —Tony Priestman
|
| | | | | Did we agree a standard for these, or are we going to go with ad-hoc inclines? On Sun, 22 Apr 2001, Huw Millington (<GC6u8C.Lnz@lugnet.com>) wrote at 09:59:14 (...) (24 years ago, 23-Apr-01, to lugnet.loc.uk)
|
| | | | | |
| | | | | | | Re: SCLF: Pasting tables &c. —Phil Traviss
|
| | | | | | | Also, will power be available? How close by? ----- Original Message ----- From: "Tony Priestman" <Tony@you-rang.demon.co.uk> To: <lugnet.loc.uk@lugnet.com> Sent: Monday, April 23, 2001 7:09 PM Subject: Re: SCLF: Pasting tables &c. (...) shop (...) (24 years ago, 23-Apr-01, to lugnet.loc.uk)
|
| | | | | | | |
| | | | | | | | | Re: SCLF: Pasting tables &c. —Jason J. Railton
|
| | | | | | | | (...) I did ask, and I was told there are power points. That's good, because it means we can put a kettle on. You'll probably need some lengthy extension leads though, to go across the room. Jason J Railton (24 years ago, 23-Apr-01, to lugnet.loc.uk)
|
| | | | | | | | |
| | | | | | | Re: SCLF: Pasting tables &c. —Huw Millington
|
| | | | | | "Tony Priestman" <Tony@you-rang.demon.co.uk> wrote in message news:lGesPFAP$G56Ewc...n.co.uk... (...) I went for a Homebase one, but I am sure we can use some plates under the legs to get the heights the same. Huw (24 years ago, 23-Apr-01, to lugnet.loc.uk)
|
| | | | | | |
| | | | | Re: SCLF: Pasting tables, etc. —Paul Cook
|
| | | | | (...) I've got a couple of Homebase ones for the train layout and possibly a third to display the Futuron & Blacktron stuff on. Huw - could you possibly bring the 6941 Blacktron Prowler (or 'Battrax') as well if you've got room? I don't have one and (...) (24 years ago, 24-Apr-01, to lugnet.loc.uk)
|
| | | | | |
| | | | | | | Re: SCLF: Pasting tables, etc. —Huw Millington
|
| | | | | | Paul Cook <astronut1@lycos.com> wrote in message news:GCAGJD.370@lugnet.com... (...) third (...) as (...) it. OK -- will do. (24 years ago, 24-Apr-01, to lugnet.loc.uk)
|
| | | | | | |
| | | | | Re: Pasting tables &c. —Lawrence Wilkes
|
| | | | | "Huw Millington" <hmillington@cix.co.uk> wrote in message news:GC6u8C.Lnz@lugnet.com... (...) I know you were not keen on putting your train MOCs etc on the floor in case they got kicked, but in my opinion the average pasting table is a pretty (...) (24 years ago, 24-Apr-01, to lugnet.loc.uk)
|
| | | | | |
| | | | | | | Re: Pasting tables &c. —Huw Millington
|
| | | | | | Lawrence Wilkes <lawrence@thewilkesf...rve.co.uk> wrote in message news:GCAH9H.4Bp@lugnet.com... (...) a (...) case (...) is (...) I've not had any collapse, but I agree they are a bit frail. Masking tape sounds a good idea, though. Huw (24 years ago, 24-Apr-01, to lugnet.loc.uk)
|
| | | | | | |
| | | | | | | | Re: Pasting tables &c. —Lawrence Wilkes
|
| | | | | | "Huw Millington" <hmillington@cix.co.uk> wrote in message news:GCAoIp.G6M@lugnet.com... (...) If you are worried about people kicking things on the floor, you would have to assume someone will kick the legs of the pasting table away too. I am (...) (24 years ago, 24-Apr-01, to lugnet.loc.uk)
|
| | | | | | |
| | | | | Re: Pasting tables &c. —Lawrence Wilkes
|
| | | | "Huw Millington" <hmillington@cix.co.uk> wrote in message news:GC6u8C.Lnz@lugnet.com... (...) I have just laid out my metro plaza and it measures 8x6 feet. I dont want to use up everyone room! Also this is quite large for pasting tables. I am (...) (24 years ago, 24-Apr-01, to lugnet.loc.uk)
|
| | | | |
