 | | Re: Problem finding standard parts in MLCAD
|
|
(...) That seems to have done it! Thanks! Jake --- Jake McKee AFOL LUGNET Member #211 (25 years ago, 6-Jun-01, to lugnet.cad.mlcad)
|
| |
| | Re: Problem finding standard parts in MLCAD
|
|
did you hit regenerate list? mine was same way heh -- And they said 'Computers will never be in general use' "Jake McKee" <sink@countersinkdg.com> wrote in message news:GEHnoC.Ftz@lugnet.com... (...) brick, (...) I (...) (25 years ago, 6-Jun-01, to lugnet.cad.mlcad)
|
| |
| | Problem finding standard parts in MLCAD
|
|
All, I am starting to actually _create_ MLCAD based models and I am having trouble locating some of the basic parts. 1x1 brick, 1x2 non-printed brick, 45 Slope 2x2 non-printed and 1x2 tile with one center stud are just a few I am having trouble (...) (25 years ago, 6-Jun-01, to lugnet.cad.mlcad)
|
| |
| | Re: zoom function
|
|
(...) Bill, For every view except 3D, this is possible, but is not a one-step process. Step 1: Click on the piece you wish to center on in "Place Mode". (The square with the pencil and arrow indicates place mode.) Step 2: Change your model from (...) (25 years ago, 5-Jun-01, to lugnet.cad.mlcad)
|
| |
| | Re: zoom function
|
|
yes that would be very nice. -- And they said 'Computers will never be in general use' "Bill Fitzgerald" <wfitz@ptway.com> wrote in message news:GEH3J9.HEF@lugnet.com... (...) from (...) part (...) (25 years ago, 5-Jun-01, to lugnet.cad.mlcad)
|
| |
| | zoom function
|
|
Is there a way to set up MLCAD so that when I do a zoom in, say change from 100 percent view to 300 percent view, to have the view centered on the part that is currently selected? It is a minor thing, but something that i would like to be able to (...) (25 years ago, 5-Jun-01, to lugnet.cad.mlcad)
|
| |
| | Re: Differences between rotation points
|
|
(...) from (...) library (...) rotation (...) That helps a lot. Thanks! Cheers, --Ryan (25 years ago, 30-May-01, to lugnet.cad.dev, lugnet.cad.mlcad)
|
| |
| | Re: Maximum Coarse movement
|
|
(...) Shure, I will take care on that. In the mean time you could move the part using the mouse and a small scale factor in the viewing pane. That should help a little bit. Michael (25 years ago, 30-May-01, to lugnet.cad.mlcad)
|
| |
| | Re: Differences between rotation points
|
|
(...) - Part Origin, is the absolute zero (0,0,0) point of the part itself. - Part Center, is the computed center of the part (e.g. the part ranges from (-2, -2, -2) to (+4, +4, +4) so the computed center is (+1,+1,+1). - The part rotation point, is (...) (25 years ago, 30-May-01, to lugnet.cad.dev, lugnet.cad.mlcad)
|
| |
| | Maximum Coarse movement
|
|
Michael, Why is the Maximum Coarse movement limited to 100? If one is moving pieces long distances frequently, using the Enter Position/Rotation dialog box can become tiresome. Could you perhaps increase the limit to, say, 250 or so? Regards, --Ryan (25 years ago, 29-May-01, to lugnet.cad.mlcad)
|
