 | | Re: primer/tutorial on BFC? [DAT]
|
|
(...) For the two-dimensional primitives (disc, ndis, ring, chrd) you can do the following: Say you have a disc in the x-z plane, like: 1 16 0 0 0 10 0 0 0 1 0 0 0 10 4-4disc.dat If this has the wrong BFC winding, you can just flip (mirror) the (...) (21 years ago, 30-Dec-03, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC? [DAT]
|
|
(...) That shouldn't work -- the rendering program should detect that you've mirrored the object, and adjust accordingly. Unfortunately, I see that it does 'work' in L3Lab. LDView is crashing my system right now, so I couldn't check it. What you (...) (21 years ago, 31-Dec-03, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC? [DAT]
|
|
(...) I do agree that it isn't supposed to work, because the BFC spec very carefully states that any polygons drawn with an aggregate matrix that causes mirroring must be flipped back. (...) I'm sorry that LDView is crashing your system, but it (...) (21 years ago, 3-Jan-04, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC?
|
|
(...) L3Lab supports BFC INVERTNEXT. /Tore (21 years ago, 3-Jan-04, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC?
|
|
(...) If this is the case then we need to go back through all the BFC'd parts and find instances of this type of matrix. Since L3Lab allows inverting the sign of the Y component and it's currently the only program to easily check for correct (...) (21 years ago, 3-Jan-04, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC? [DAT]
|
|
(...) I think it works just fine. L3Lab correctly detects that the matrix is mirroring, see View/Tree View... and click the BFC radio button, it should say INVERT in front of the line. When we discussed the BFC business the general assumption was (...) (21 years ago, 3-Jan-04, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC?
|
|
(...) I do this all the time, too. Just a minus sign in stead of 'BFC INVERTNEXT' each time can save some diskspace, which I've been told is something to go for, too. Niels (21 years ago, 3-Jan-04, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC?
|
|
(...) You're right; I'm wrong. I'm still having a hard time visualizing it, but your stud example below convinced me that negating the one value in the matrix will indeed flip a 2D primitive like a disk, and this is the expected behavior. In fact, (...) (21 years ago, 3-Jan-04, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC?
|
|
(...) Actually, I *think* it's the new ATA controller card I installed, and LDView was just an innocent bystander. However, since LDView doesn't do BFC, I guess I didn't miss anything. (...) Yes, you could use INVERTNEXT, but that introduces (...) (21 years ago, 4-Jan-04, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC?
|
|
(...) Hmmm, very good point. I don't like treating specific object specially, but I don't see any way around it. I played around with the stud and with a 'solid' cylinder object, I couldn't find a way to get L3Lab's BFC handling to fail. Steve (21 years ago, 4-Jan-04, to lugnet.cad.dev)
|
| |
| | Re: primer/tutorial on BFC?
|
|
(...) [snip] (...) I just wanted to add one more post in an attempt to clear up any confusion that may have been caused in this thread. What Andy says above is correct, and my earlier post indicating otherwise was incorrect. The two dimensional (...) (21 years ago, 4-Jan-04, to lugnet.cad.dev)
|
