 | | Re: BFC: LITS 2
|
|
(...) I think the discussion started before the "line in The Sand" thread ! (...) It seems that it is currently on version 9 ! isn't it ?, but file name was NOT changed, OK. (...) Well, if my memory doesn't fail me, I taught you were against local (...) (25 years ago, 2-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: Time for BFC overhaul?
|
|
(...) Didn't answer the question, but moving on. (...) That's good to know. (...) Yes, but the proposed standard doesn't list the several options for a specific issue thta asn't been agreed iet. List the options, that's my point, because if you (...) (25 years ago, 2-Apr-00, to lugnet.cad.dev)
|
| |
| | LDS ver 0.31 - Added PIPE
|
|
New version again. Same URL as usual. (URL) /Tore (25 years ago, 2-Apr-00, to lugnet.cad.dev, lugnet.cad)
|
| |
| | Re: A discovery? and part 3475
|
|
(...) Oops, sorry 'bout that. (...) Wow, you're working with the horse? You have my deepest respect! I think that using one tool or another is mostly a matter of taste. I haven't written LDraw-mode to compete with anybody else's tool, but because I (...) (25 years ago, 2-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: A discovery? and part 3475
|
|
(...) Not just 4-4edge - it takes all between 1/16 through 16/16 and 1/48 through 48/48. (...) I see (I think...) If the two arbitrary connected curves run parallelly, I use LDS' EXTRUDE function, if not, I have to make arrangements like this in (...) (25 years ago, 2-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: A discovery? and part 3475
|
|
(...) related. Quite a coincident! Your function takes two (or more) 4-4edge primitives and connects them with quads, to create a "pipe" like object. My function takes two arbitrary connected curves made up of type-2 lines and fills in the space (...) (25 years ago, 2-Apr-00, to lugnet.cad.dev)
|
| |
| | Re: A discovery? and part 3475
|
|
I haven't followed this thread, but after a brief glance, I think it is closely related to the PIPE function I (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: A discovery? and part 3475
|
|
(...) I have made a function in LDraw-mode which does this. In your example, you would put the cursor on the first type-2 line in the first edge, set the mark (C-SPC) move down to the first type-2 line in the second curve and hit C-c C-f. Voila. The (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Type-5 conditional edge line
|
|
I have a question about the type-5 conditional line. Assume I have four points in 3d space like this: (If you're reading LUGNET via the web interface, you must push "view raw message" to see my ASCII art.) 1---2 | | | | | | 4---3 Except that the (...) (25 years ago, 1-Apr-00, to lugnet.cad.dev)
|
| |
| | PIPE function... [DAT]
|
|
I've made a new function for LDS called PIPE. It's an extension of the LINE function. Remember:? LINE POINT x y z POINT x y z ... POINT x y z LINE END Now, PIPE works the same way but with that difference it's in 3D: PIPE [n_sectors total_sectors] (...) (25 years ago, 1-Apr-00, to lugnet.cad.dev)
|
