 | | Re: Organizing the LDraw CD-ROM
|
|
(...) of (...) I haven't been following this thread to closely, but uh, are you considering machines that are not running Windows. LdGLite 0.4 is due to be released real soon and should run pretty well on Linux and the Mac in addition to Windows. (...) (25 years ago, 11-Feb-00, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Organizing the LDraw CD-ROM
|
|
(...) You'll find out, and yes, it is a layout-type program. Get it setup the way you want it, and if I can take your saved project file and just compile it (you'd have to give me a place to grab the cd from, or maybe burn one copy for me) and burn (...) (25 years ago, 11-Feb-00, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Looking for a part
|
|
(...) as (...) wife (...) Mishandling would seem to unlikely. With no visible sign of distortion they appear to have been molded that way. Do you want me to send you one of each? (...) I agree that we would should draw it at 90deg., with maybe a (...) (25 years ago, 11-Feb-00, to lugnet.cad.dev)
|
| |
| | Re: 8448 Flexible Axles (was Re: Parts from 8448 not LDrawn)
|
|
(...) Juth put them into technic. -- Jonathan Wilson wilsonj@xoommail.com (URL) (25 years ago, 10-Feb-00, to lugnet.cad.dev)
|
| |
| | Re: Looking for a part
|
|
(...) I wrote 9 degrees from memory. I couldn't locate the previous discussion. (...) least three Spaceport sets, and the Mos Espa Podrace set. (...) Hmm. I wonder what caused the variation. A few ideas: 1. Differences between the molds in the (...) (25 years ago, 10-Feb-00, to lugnet.cad.dev)
|
| |
| | Re: 8448 Flexible Axles (was Re: Parts from 8448 not LDrawn)
|
|
(...) Found it! (URL) They were *not* introduced in Znap. But the odd length axle with the stop-collar *was* introduced in Znap. (URL) So, should these parts be included in Technic, or should a new category for Znap be started? Steve (25 years ago, 10-Feb-00, to lugnet.cad.dev)
|
| |
| | Re: 8448 Flexible Axles (was Re: Parts from 8448 not LDrawn)
|
|
(...) Ah! Thank you, Wayne. (...) From the rumblings in lugnet.loc.uk, it doesn't seem likely -- people only appreciate Znap when it's on clearance. :-/ Steve (25 years ago, 10-Feb-00, to lugnet.znap, lugnet.cad.dev, lugnet.dear-lego)
|
| |
| | Re: 8448 Flexible Axles (was Re: Parts from 8448 not LDrawn)
|
|
(...) The first use is on page 153 (book 2). They're used to make the curves in the body-lines. Steve (25 years ago, 10-Feb-00, to lugnet.cad.dev)
|
| |
| | Re: 8448 Flexible Axles (was Re: Parts from 8448 not LDrawn)
|
|
(...) Were *what*? Steve (25 years ago, 10-Feb-00, to lugnet.cad.dev)
|
| |
| | Re: stl2dat conversion tool beta2
|
|
(...) STL only support triangles. Nurbs (and other geometry) must be converted by the CAD software to triangles. That's why I choosed STL : it already contains triangles and that's very near LDraw format. (In a geometric point of view) (...) Yes, I (...) (25 years ago, 10-Feb-00, to lugnet.cad.dev)
|
