 | | Re: "33" Slope Shocker... Possible name change?
|
|
(...) Steve, I'm thinking it would be of more use to name the parts using a "Rise/Run" method, like in architecture. When using the LEGO pieces the important thing is not the actual angle on the sloped face, anymore than it is the actual height, (...) (24 years ago, 14-Apr-01, to lugnet.cad.dev)
|
| |
| | Re: "33" Slope Shocker... Possible name change?
|
|
(...) :) Or a comment line in the base-part file, noting the proper orientation for decorations on the slope-face. Steve (24 years ago, 11-Apr-01, to lugnet.cad.dev)
|
| |
| | Re: "33" Slope Shocker... Possible name change?
|
|
"James J." <jejackso@memphis.edu> wrote in message news:GBHo7t.911@lugnet.com... (...) According to the "Lego Dimension Guide" I have that was created by Onyx (I think) the angle is 26.565 degrees. That is what I use and it hits it perfect every (...) (24 years ago, 10-Apr-01, to lugnet.cad.dev)
|
| |
| | Re: Advice please on DATs for bendy-arm holder 2x2 brick
|
|
(...) pieces (...) No. Clipping. (...) separate (...) in (...) The composite parts have been posted at (URL) and (URL) also done the proximal bendy-arm part to be used with these holders (URL) send the separate parts files to parts@ldraw.org Chris (...) (24 years ago, 10-Apr-01, to lugnet.cad.dev)
|
| |
| | ldraw.org off-line from 8:00 to 8:30 (Danish time)
|
|
I move the ldraw.org server to a proper server room in a moment. Expect half an hour of downtime. Play well, Jacob (24 years ago, 10-Apr-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: "33" Slope Shocker... Possible name change?
|
|
(...) Ouch. Now that is some number. I looked it up in both the Windows Calculator and AutoCAD 2000 (expanding tolerance out to the smallest decimal -- hundred millionths) to find out the your large figure rings true. (...) *huff, puff* I'm inclined (...) (24 years ago, 9-Apr-01, to lugnet.cad.dev)
|
| |
| | Re: "33" Slope Shocker... Possible name change?
|
|
This problem has (probably) been realized by a number of people in the last few years; I figured it out (or was it pointed out to me?) a few months ago. Yes, I am planning on doing a mass name-change, but after the automated Parts-Tracker is up and (...) (24 years ago, 9-Apr-01, to lugnet.cad.dev)
|
| |
| | "33" Slope Shocker... Possible name change?
|
|
Greetings. I have made a new discovery that may seem all too obvious to everyone else who has actually programmed elements in LDraw or MLCAD. My discovery is as follows: All bricks listed as having a 33-degree slope are not named with correct (...) (24 years ago, 8-Apr-01, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: Unplanned downtime for ldraw.org
|
|
(...) I see the BOFH is up to his old tricks again then? ;-) alex (24 years ago, 6-Apr-01, to lugnet.cad.dev.org.ldraw, lugnet.off-topic.fun)
|
| |
| | Unplanned downtime for ldraw.org
|
|
Some jerk has pulled out a cable from the ldraw.org server, so the machine will be off-line for at least two more hours, and maybe until tomorrow morning (DK time). Play well, Jacob -- Beware of the system operator... (24 years ago, 6-Apr-01, to lugnet.cad.dev.org.ldraw)
|
