 | | Re: LDlite 1.6 problems
|
|
(...) <dennett@agate.net> (...) it's (...) I never (...) LDAO -- I (...) of LDAO. (...) I am using LDAO version 1.4.5 because the next version and the beta both have the "disappearing cursor" on my computers. I am not sure, but it seems like my not (...) (25 years ago, 4-Aug-99, to lugnet.cad.dev)
|
| |
| | why is the roadsign round with no throughoufare sign called 7284?
|
|
why is the roadsign round with no throughoufare sign called 7284? is this the TLG number? (25 years ago, 3-Aug-99, to lugnet.cad.dev)
|
| |
| | Re: Voting page for 9906
|
|
(...) things i know about: what exactly is missing fron the box and switch??? i cant see any details on the part that can be seen from the outside that are missing except the clip. i will add the rectangular face part of the clip to the lid part if (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Re: Voting page for 9906
|
|
(...) Okay, I checked my canopies, and here is what I found: 2 are as John is describing. Very little fading from Dark to light gray, no gray line on the inside, etc. These correspond to my Y-wing sets. 6 are as I'm describing. Fade from dark to (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Re: LDlite 1.6 problems
|
|
(...) Huh? That's probably a problem with your LDAO-to-LDLite setup. I never have any problems this way (and I constantly launch LDLite from LDAO -- I use LDAO's editors). (...) These two might be a problem if you are using the current beta of LDAO. (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev)
|
| |
| | LDlite 1.6 problems
|
|
I have been having tons of problems with Ldlite 1.6 I know it's been out for quite a while, but I don't use it much so I never bothered to say anything. I'll list the problems below. I haven't had any problems with previous versions of Ldlite. Can't (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev)
|
| |
| | Re: Voting page for 9906
|
|
Voting part comments: 2400, 6105: The 1/2 cylinder studs on the doors need 4-4edge.dat's where they meet the flat part of the door. 2500c01: I don't think the lights are done quite right here. There's a reference to a 4-4cone1.dat, but I don't have (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Re: Baseplate 32 x 32 Raised with Ramp (fixed version)
|
|
(...) Can I suggest a protocol change?: Especially when dealing with large parts (like baseplates), before submitting a "fixed" part to .cad.dat.parts, send it first via email to the person who pointed out the error to you, so that they can confirm (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev)
|
| |
| | Re: Voting page for 9906
|
|
(...) news:FFuFFw.Cr0@lugnet.com... (...) Ah. I didn't realize that. No problem then. (...) Really? I'll have to compare all of mine when I get home (I have 8). Don't forget to dither(?) the dark gray to light gray, please! :) I could deal with a (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
| |
| | Re: Voting page for 9906
|
|
Jeff Stembel <Dragonelf1@aol.com> wrote in message news:FFuFFw.Cr0@lugnet.com... (...) The insertion point is the center of the cylinders. This makes it much easier to rotate on the z axis, and to rotate on the x axis then place in its vertical (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
