 | | Re: OMR Submission and Storage
|
|
(...) So basically no difference, really. That is, you can visually scan a hundred messages for "OMR" in a second or two -- or even faster with a script -- but where 99.9% of the time goes is verifying the quality of the model. So pulling down 5 new (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: OMR Submission and Storage
|
|
(...) If you mean 2429/2430, it's already centered! If you mean 4275/4276, you can use the method outlined in my LDraw Tutorial, using light.dat as a place-holder for the origin (0,0,0). You'll have to look at a couple different views to make sure (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: LDLITE and LDAO
|
|
(...) Thanks for the link, I haven't figured that one out yet either... (...) Comments? Who's comments? I don't believe I've met him before ;) -Tim <>< (URL) timcourtne ICQ: 23951114 Get paid to surf the web! Visit: (URL) (25 years ago, 23-Jul-99, to lugnet.cad.dev)
|
| |
| | Re: LDLITE and LDAO
|
|
(...) This page is linked from the front page for LDAO: (URL) is, should LDAO / LDLite Q&A go into the LDraw FAQ, or specifically into the LUGNET FAQ, or someplace altogether? Steve? Paul? Comments? Cheers, - jsproat (25 years ago, 23-Jul-99, to lugnet.cad.dev, lugnet.faq)
|
| |
| | LDLITE and LDAO
|
|
How do I set up LDAO to use LDLITE? Thanks, Adam (25 years ago, 23-Jul-99, to lugnet.cad.dev)
|
| |
| | Re: OMR Submission and Storage
|
|
(...) Searching through a potential lot of messages for the word 'OMR.' (...) But posting a submission to an OMR group and casually posting to a sets group are in fact different. One there is strict requirements for, the other there isn't. So it (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: OMR Submission and Storage
|
|
(...) So do I. But I probably wouldn't subscribe to a sets or omr newsgroup by mail. It would work, but why not avoid possible confusion and go for 100% certainty on a completely new dedicated newsgroup? Some people might think that (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: OMR Submission and Storage
|
|
(...) Yes. Those that are non-instruction submodels but purely for ease of modelling are definitely acceptable. (I gotta remember to throw that one in the creation/submission guide) (...) Good thoughts. I would say that the models which do not (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | About LDraw/LEdit Part 4212
|
|
I have been trying to acquire and use the car frame from #6390 Main Street & #6375 in LDraw. (URL) will note that it's different from the one in #6634, 6525, and other sets made after 1983. The bottom is smooth and cannot support a 2x4 plate (...) (25 years ago, 22-Jul-99, to lugnet.cad.dev)
|
| |
| | Re: OMR Submission and Storage
|
|
(...) of rotation. (...) haven't been (...) everyone else (...) do?? (...) Just how do you center it on the hinge part of a 1x2 hinge plate (:-I I have yet to figure out how to do that, so I guess that means I've got a pea-sized brain too. :) Ryan (25 years ago, 22-Jul-99, to lugnet.cad.dev.org.ldraw)
|
