 | | Re: 2867.dat Curved 9V Track - reddy
|
|
(...) Very nice! Good work on this. :) However (I always seem to have a 'however' ;), I'm not sure about your choice of the zero-point and the orientation of the part. The point you chose was very logical, but it might not be practical. In relation (...) (21 years ago, 19-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | Re: 9V Curved Track
|
|
(...) The information i have abouth parts center comes from the LDRAW FAQ - Question24 Steve Bliss writes : Quote Tip#1: The Ldraw standard for positioning is to the center of the piece on X=0 and Z=0. Usually, the top of the part (excluding studs) (...) (21 years ago, 17-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | Re: 2867.dat Curved 9V Track - ready
|
|
(...) <SNIP> (...) Perhaps not for you, but without this little piece of software wouldn't i be able to create this part. It was just THIS that make me believe that i could create this part. I'm not a mathematic gouru, and trust me, i'm going to (...) (21 years ago, 17-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | Re: 9V Curved Track
|
|
(...) ... (...) It's the 'normal' part that trips me up! Consider these parts: (URL) a geometry point of view, these are pretty similar. But (according to MLCad) the center of the macaroni is the circle center; the center of the 2x2 'L' is the (...) (21 years ago, 17-Apr-03, to lugnet.trains, lugnet.cad.dat.parts)
|
| |
| | Re: 2867.dat Curved 9V Track - ready
|
|
Great! Many thanks for the enormous work you have laid down in this part. /Tore Eriksson (without 'c') (...) Ah, nothing to mention. :o) (...) (21 years ago, 17-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | 2867.dat Curved 9V Track - reddy [DAT]
|
|
Hi, Here's the promessed 9V curved track. It's a bit earlier than announced a few days ago, i could work sunday the whole day on it. I hope you like it, and that there arent too many errors in it. If any errors found, let me know, so that i can make (...) (21 years ago, 16-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part - Guared Inn Flag with goblets Subpart 2/2 [DAT]
|
|
0 ~Flag 2 x 2 with Goblets & Grapes Pattern - Gold Detail 0 Name: s\2335ps4b.dat 0 Author: Bernd Broich 0 Unofficial Part 0 BFC CERTIFY CW 0 Goblet 1 16 0 23.25 39.125 0 -1 0 0 0 -2.5 -2.375 0 0 1-4disc.dat 1 16 0 25.125 20.75 0 -1 0 -3.875 0 0 0 0 (...) (21 years ago, 14-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part - Guared Inn Flag with goblets Subpart 1/2 [DAT]
|
|
0 ~Flag 2 x 2 with Goblets & Grapes Pattern - Silver Detail 0 Name: s\2335ps4a.dat 0 Author: Bernd Broich 0 Unofficial Part 0 BFC CERTIFY CW 0 Frame 4 16 0 34.75 15.25 0 34.75 44.75 0 37.5 47.5 0 37.5 12.5 4 16 0 34.75 44.75 0 5.25 44.75 0 2.5 47.5 (...) (21 years ago, 14-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | New Part - Guared Inn Flag with goblets [DAT]
|
|
I made the flag with goblets from the Guarded Inn set. I needed to do that because I found it after years behind the furniture. I post it here because the tracker isn't online. PLMKWYT 0 Flag 2 x 2 with Goblets and Grapes Pattern 0 Name: 2335p40.DAT (...) (21 years ago, 14-Apr-03, to lugnet.cad.dat.parts)
|
| |
| | Re: 2867.dat Curved 9V Track
|
|
Looks Great : ) (...) (21 years ago, 13-Apr-03, to lugnet.cad.dat.parts)
|
