 | | New Part - Brick 2 x 2 Round with Buttons Pattern [DAT]
|
|
I found it in Set No 6394 - Service Station CU Bernd 0 Brick 2 x 2 Round with Buttons Pattern 0 Name: 3941p01.dat 0 Author: Bernd Broich 0 Unofficial part 0 Original Part 1 16 -10 0 -10 1 0 0 0 1 0 0 0 1 stud.dat 1 16 -10 0 10 1 0 0 0 1 0 0 0 1 (...) (23 years ago, 18-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | 2618.dat Auqanaut Bubble Base (Updated) [DAT]
|
|
Thanks to Carston for his helpful post. For some reason LDDesignPad didn't list any errors. I had to run L3P in DOS mode. Anyway, here's the updated DAT, L3P error free. -Orion 0 Aquanaut Bubble Base 0 Name: 2618.ldr 0 Author: Orion Pobursky 0 (...) (23 years ago, 17-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: 2618.dat Auqanaut Bubble Base (Final, I Hope)
|
|
Hello Orion! (...) As (...) Amazing part! I don't know if this is your first part but it looks very good and i bet it was some hard work! Two things i noticed. - Some missing lines at the egdes of the four half-button prints (bottom of part) - Check (...) (23 years ago, 17-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | 2618.dat Auqanaut Bubble Base (Final, I Hope) [DAT]
|
|
After 2 weeks of tweaking I think I am finally ready to release my part. As this is my first part, please let me know if I made any part authoring no-no's or if you have any improvements to suggest. Thanks -Orion Pobursky 0 Aquanaut Bubble Base 0 (...) (23 years ago, 17-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: 2x4 left and right half wedge brick and plate
|
|
(...) Actually, I need an *income* (i.e., a job) first. :-/ *Then* I can start acquiring more new LEGO. >:-D (...) I haven't found a dirt-cheap (under $10) set with those parts at a local store, yet. :-/ Thanks, Franklin (23 years ago, 16-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: 2x4 left and right half wedge brick and plate
|
|
(...) Sounds like you need to pick up a Jedi Starfighter ;) You did a great job on the other 6 new curvey/slopey parts, btw. Thanks! They're just what I needed for my current project. Alas, I still need the 2x4 half wedge plates. I'm really (...) (23 years ago, 16-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Parts tracker - how do I get in touch with a reviewer?
|
|
"Franklin W. Cain" <fwcain@yahoo.com> wrote in message news:Gt1qBF.DG6@lugnet.com... (...) It still took time and patience to get the patterns right, and you did so many! I couldn't have created some of my models without those parts. (...) I sort of (...) (23 years ago, 16-Mar-02, to lugnet.cad.dev.org.ldraw, lugnet.cad.dat.parts)
|
| |
| | Re: Stud Primitive Question
|
|
I'm a moron. I had studs on low resolution and thought they were 8 sided. My mistake. -Orion (23 years ago, 16-Mar-02, to lugnet.cad.dat.parts, lugnet.cad.dat.parts.primitives)
|
| |
| | Re: 2x4 left and right half wedge brick and plate
|
|
(...) I don't have these parts "in hand", otherwise I'd be happy to do them for you. (One is not supposed to attempt to encode pieces or patterns one has not physically examined.) Franklin (23 years ago, 16-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Parts tracker - how do I get in touch with a reviewer?
|
|
(...) Thanks for the vote of confidence. But, seriously, when I really took a good look at those minifig heads (in real life), I said, "Hey! These look *really* similar! Once I do this one, I can make just a few changes and I'll have this one, then (...) (23 years ago, 16-Mar-02, to lugnet.cad.dev.org.ldraw, lugnet.cad.dat.parts)
|
