 | | 2865.dat - 9V straight track re-release [DAT]
|
|
Hi, This is a re-release of the earlier posted 2865.dat file from abouth 2 years ago. It's been completely re-written, and i have to thank Manfred Moolhuysen a thousand times for his tremendious help.It's a lot more realistic than previous release (...) (23 years ago, 14-Feb-02, to lugnet.cad.dat.parts)
|
| |
| | Re: upload one main file & 4 subparts
|
|
(...) You can turn the files into an MPD. The layout of an MPD is like: 0 FILE mainfile.dat <contents of mainfile.dat> 0 FILE subfile1.dat <contents of subfile1.dat> 0 FILE subfile2.dat <contents of subfile2.dat> 0 FILE subfile3.dat <contents of (...) (23 years ago, 13-Feb-02, to lugnet.cad.dat.parts)
|
| |
| | Re: upload one main file & 4 subparts
|
|
(...) Ludo, The short answer is, "one (file/message) at a time"... Create five separate messages, uploading one file per message. I'd recommend that you upload the four subfiles *first*, so that you can reference their URLs when you post the *main* (...) (23 years ago, 13-Feb-02, to lugnet.cad.dat.parts)
|
| |
| | upload one main file & 4 subparts
|
|
Hi, How can i upload a main file and the 4 nesesarry subparts to this location? Regards, Ludo (23 years ago, 13-Feb-02, to lugnet.cad.dat.parts)
|
| |
| | Re: New stud 4 primitive for plates with holes [DAT]
|
|
(...) If you made this a subpart (instead of a primitive) and included the original stud4 primitive you'd save more space and possibly avoid the square hole problem? Of course then you have the problem of that undesireable edge line on the inside of (...) (23 years ago, 12-Feb-02, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: New stud 4 primitive for plates with holes [DAT]
|
|
"Mark Kennedy" <mkennedy@peak.org> schrieb im Newsbeitrag news:GrFCoL.MzM@lugnet.com... (...) Stud4 files are in the bottom of a piece and possible they need to stretch sometimes. So the height of the hole is not constant. So I think it's easier to (...) (23 years ago, 12-Feb-02, to lugnet.cad.dat.parts.primitives)
|
| |
| | New stud 4 primitive for plates with holes [DAT]
|
|
Here is a new version of the stud 4 primitive for use in technic plates and other parts with holes in the plates. By including the ndisks into the primitive they can be ommited from the part thus saving space, the bad news is that when you turn (...) (23 years ago, 12-Feb-02, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: New Part: 168135a.dat - Sticker Technic Supercar 4x4x4 Logo
|
|
(...) Hmm. I opened this in LDLite 2.4, put it into 'twirl mode', and there was some serious bleedthru at various (odd) angles. I didn't try twirling the original (1LDU-high) file. LDraw and LEdit handled the file just fine. But I didn't try to (...) (23 years ago, 6-Feb-02, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 168135a.dat - Sticker Technic Supercar 4x4x4 Logo [DAT]
|
|
I made some modification: 1. Changed the filename as Steve suggested. 2. Reduced the thickness (thinness? :-))of the thin box to 0.25 LDU as Bernd Broich suggested. In L3Lab it did'nt cause any bleed-through. 3. Included a placeholder in the part (...) (23 years ago, 6-Feb-02, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 168135s01.dat - Sticker Technic Supercar 4x4x4 Logo
|
|
Hi all, (...) I think the height of the box can be 0.2-0.25 LDU (0.2 is the minimum I tested in some LCAD-programs), this is in the near of the real thickness of the stickers. (...) I also have a lot of stickered parts and want to make them, but I (...) (23 years ago, 5-Feb-02, to lugnet.cad.dat.parts)
|
