 | | Re: technic engine piston square 2x2 [DAT]
|
|
Bart, Try this for the curves from the sides to the top: 1 16 18 2 18 2 0 0 0 0 -2 0 -36 0 1-4cyli.dat 1 16 18 2.0 16 0 0 2 -2 0 0 0 2 2 1-4cyli.dat 1 16 18 2.0 18 0 0 2 -2 0 0 0 2 2 1-4edge.dat 1 16 18 2.0 -18 0 0 2 -2 0 0 0 2 -2 1-4cyli.dat Of (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: 6246f: Minifig Oilcan
|
|
i do not have the slope so i cant do it. (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: tapbase also
|
|
This part looks good. -John Van (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: tap part number
|
|
The tap base needs edgelines where the handle meets the faucet, and at the base. -John Van Bart Titulaer <b.m.titulaer@phys.tue.nl> wrote in message news:FEur7M.Fpx@lugnet.com... (...) yesterday (...) author), I (...) yesterday, (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: 6246f: Minifig Oilcan
|
|
Jonathan Wilson <wilsonj@xoommail.com> wrote in message news:378BCAD2.9B03F6...ail.com... (...) x-wing you possibly can... keep up the good work. now, asside from the minifig parts all we need is the death star slope. Yup. I've actually begun work (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | Re: 6246f: Minifig Oilcan
|
|
[followups set to lugnet.cad.dev] Nice job! Now I don't have to worry about that entry on the Parts Tracker anymore. :) The power drill could be modified. I doubt it's seen much use. Especially not in situations where the position is (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: My first part
|
|
(...) If there are two different patterns, then the ?? will be replaced with two different two-digit numbers. Just like we've always done. Steve (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | technic engine piston square 2x2 [DAT]
|
|
Hi, I'm not sure about the name, number and description and not about the lines in combination with the rounded edges. Any comments and or suggestions? Bart Titulaer 0 technic engine piston square 2x2 0 Name: pistonSQR.DAT 0 Author: Bart Titulaer 0 (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | tapbase also [DAT]
|
|
nothing changed, but I'm not sure wether it's already available on lugnet.com 0 Homemaker Tap Base 0 Name: tapbase.dat 0 Author: Tore Eriksson 0 Un-official Part 4 16 -20 0 -10 20 0 -10 16 0 -6 -16 0 -6 4 16 -20 0 10 20 0 10 16 0 6 -16 0 6 4 16 -20 (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
| |
| | tap part number [DAT]
|
|
Hi, Jonathan send me yesterday this unofficial part, I've completed it. Tore Eriksson was and is the author (I should have asked you, but I saw it yesterday evening after I had finished it. I thought Jonathan was the original author), I think the (...) (25 years ago, 14-Jul-99, to lugnet.cad.dat.parts)
|
