 | | Gorgon [DAT]
|
|
Finally figured out how to use the "inline" button, duh. Here is an older model I have done that might make it to a web page someday. It was originally intended to look like Luke's T-16 Skyhopper from Star Wars. In the end, I didn't have a decent (...) (25 years ago, 16-May-99, to lugnet.cad.dat.models)
|
| |
| | Fallingwater [DAT]
|
|
Here's the model I made of Fran Lloyd Wright's Fallinwater (selectively compressed of course). In real life, I built the model on two baseplates, a 48 x 48 on the bottom, and then a 32x32 with some small baseplates about 6 bricks up. I also built a (...) (25 years ago, 16-May-99, to lugnet.cad.dat.models)
|
| |
| | Re: MOC: Water Tower
|
|
In lugnet.cad.dat.models, "Ben Gatrelle" <ben.gatrelle@nospam...foot.com>: (...) Say Ben, A couple quick questions: - That file was 429 KB*. How big would it be if the parts weren't inlined? - Did you really have to inline the parts? --Todd * (...) (25 years ago, 14-May-99, to lugnet.cad.dat.models)
|
| |
| | MOC: Water Tower [DAT]
|
|
See a POV-Ray rendering of this model at my web site or download the DAT file there. (URL) 0 Water Tower by Ben Gatrelle 0 0 Water Tower top of dome 0 Inlined: 1 0 -22 -464 -10 1 0 0 0 1 0 0 0 1 watert-4.dat 0 top dome of tower 0 Name: WaterT-4.DAT (...) (25 years ago, 14-May-99, to lugnet.cad.dat.models)
|
| |
| | Re: Custom TIE/ln Fighter
|
|
Very nice, Jeff. Your model shows that the TIE could have been done just fine without the new "blocky" bracket pieces. I'll bet your wings even come off easily enough. I wish there were a good way to model the diagonal lines on the wings, though. (...) (25 years ago, 13-May-99, to lugnet.cad.dat.models)
|
| |
| | Re: Custom TIE/ln Fighter
|
|
(...) good stuff, jeff makes a great companion model to the official darth's tie ..joseph g (25 years ago, 13-May-99, to lugnet.cad.dat.models)
|
| |
| | Custom TIE/ln Fighter [DAT]
|
|
This is my custom TIE Fighter. It is missing the 2x2 cylinder tiles with the Empire's Symbol (replaced with a plain one) and the Cockpit dome, but it should be easy to spot where they are supposed to go. Jeff 0 T.I.E Fighter 0 Name: TIE_Ftr.dat 0 (...) (25 years ago, 13-May-99, to lugnet.cad.dat.models)
|
| |
| | Re: 8216 Turbo 1 - My first shot at ldraw
|
|
(...) Actually the "Hoser" program is a spreadsheet used for generating the system-type flexible hoses. It wouldn't really work well for the flex tubing. At some point in the distant future (at least after the novelty of SW Lego sets wears off) I (...) (25 years ago, 9-May-99, to lugnet.cad.dat.models.sets)
|
| |
| | Re: 8216 Turbo 1 - My first shot at ldraw
|
|
(...) I was not aware that such a program existed or I would have used it. Can you point me to where I can get it and I will update the MPD to replace the bezier curves and add the missing parts. -- Owen (25 years ago, 9-May-99, to lugnet.cad.dat.models.sets)
|
| |
| | Re: 8216 Turbo 1 - My first shot at ldraw
|
|
good first shot. 1. how about replacing bezier curve generated curve with one made by the hoser program? 2.next tile put the unofficial parts into the mpd. makes things easier. (25 years ago, 8-May-99, to lugnet.cad.dat.models.sets)
|
