 | | Re: New part, needs number: Minifig Kettle Helm [DAT]
|
|
(...) I think they are necessary. If you use this part with the armor, the notches are the cutouts from the armor edges. See this: 1 8 0 0 0 1 0 0 0 1 0 0 0 1 2587.dat 1 8 0 -27 0 1 0 0 0 1 0 0 0 1 helm.dat 1 14 0 -27 0 1 0 0 0 1 0 0 0 1 3626b.dat 1 (...) (24 years ago, 13-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Datsville rev 014. Datsville expanding again!
|
|
(...) I have as promised put my masons to work, and now there is a safe version of the building too: (URL) well, Jacob -- Houses by Katrine, Caroline and Jacob: (URL) (24 years ago, 13-Sep-02, to lugnet.cad.dat.models)
|
| |
| | Patterned parts and printing artifacts
|
|
I recently had the following exchange with SEB and CD who allowed me to post their responses to my questions. I welcome comments from others on this topic. Thanks! Larry said: (...) Steve replied: (...) Sure. I don't have any of these parts (...) (24 years ago, 13-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | Re: New part, needs number: Minifig Kettle Helm
|
|
(...) My first glance opinion -- it rocks, Baby! -- Hop-Frog (24 years ago, 13-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | New part, need pattern #: Shield Ovoid with Bull's Head Pattern [DAT]
|
|
The colors for this look pretty good for LDView and L3P/POV, but not too good with MLCad. Andy 0 FILE 770bull.dat 0 Minifig Shield Ovoid with Bull Head Pattern 0 Name: 770bull.dat 0 Author: Andrew Westrate 0 Unofficial Element 0 BFC CERTIFY CCW 1 (...) (24 years ago, 13-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | New part, needs number: Minifig Kettle Helm [DAT]
|
|
A couple of notes about this piece: I don't know if "Kettle Helm" is even close to being correct, so name suggestions are welcome. I left out the notch at the back of the neck, because it was easier to do with primitives and didn't seem too (...) (24 years ago, 13-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | Re: dragon parts
|
|
(...) Now they are finished. They can be found at: (URL) BB (24 years ago, 11-Sep-02, to lugnet.cad.dat.parts)
|
| |
| | Re: santa fe -poster- in progress
|
|
(...) I just tried this - it works very very well!! And it's not obtrusive at all. Thanks a million!! - Bob (24 years ago, 11-Sep-02, to lugnet.cad.dat.models, lugnet.trains)
|
| |
| | Re: santa fe -poster- in progress
|
|
Try this one: (URL) add 2 brackets 2x2, in gray of course :-) Even better if you mount it on top of the 1x2plate+corner plates. Good luck! Klaas H. Meijaard (...) (24 years ago, 11-Sep-02, to lugnet.cad.dat.models, lugnet.trains)
|
| |
| | Re: 1381 Vampire Crypt figs (and garlic tile)
|
|
(...) That is how I've coded up minifig heads in the past. Mentally divide face 45 degrees either side of the centre line and draw the region from +45 to -45 as a plane, then project that onto the four facets of the hexdecagon. Then if necessary, do (...) (24 years ago, 10-Sep-02, to lugnet.cad.dat.parts)
|
