 | | Re: Wheel holder pin
|
|
(...) they all use the same structure? Are you making a part that is going to use this primitive? Steve (24 years ago, 29-May-02, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: The Mummy (from "Adventurers" theme)
|
|
(...) You should move the remaining 'outside front' surfaces from the leg subfiles to the blank main files, and update the existing printed-leg parts to match the changes. That requires updating 6 official files, and your 3 unofficial files. (...) (24 years ago, 29-May-02, to lugnet.cad.dat.parts)
|
| |
| | Re: part 30592 (NAME??)
|
|
(...) Heh. You're right, this is a complex one. Previously, we've tended to not (always) note cut-outs or details -- look at the various curved brick or arch parts with 'plate-tabs' at the top. So, for this file, I'd go with 'Brick 2 x 4 x 2/3 with (...) (24 years ago, 29-May-02, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 973P73 - Minifig Torso with Vest with Patch Pockets pattern
|
|
(...) Not clearly; I think the discussion was limited to parts which appeared in multiple neck-stripe colors, not *which* neck-stripes colors we were going to use. (...) Yes, that's the bit I remember clearly. .... I did some digging, and came up (...) (24 years ago, 29-May-02, to lugnet.cad.dat.parts)
|
| |
| | Re: subfile for new part (Rebel *A-wing* pilot torso)
|
|
(...) Oh, probably. Except it needs to be rewritten to describe what to do, instead of what not to do. :) (...) True, but I think we covered the filenames well enough that the exception is adequately handled. (...) What are your feelings about (...) (24 years ago, 29-May-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Baseplates with pattern
|
|
(...) Well, that's a bit of good news. I think. :) At least, it removes one issue from the table. Steve (24 years ago, 29-May-02, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 973P73 - Minifig Torso with Vest with Patch Pockets pattern
|
|
(...) I'm still catching up on everything after getting back from Colorado; I wanted to quickly supply the answer to your question. For CMDLINE, look on page (URL), question "What is the CMDLINE meta-statement?". For KEYWORDS (and CATEGORY), look on (...) (24 years ago, 29-May-02, to lugnet.cad.dat.parts)
|
| |
| | Re: The Mummy (from "Adventurers" theme)
|
|
(...) (URL) Then, I'll encode the Legs. Which leads me to a quandry... (...) I'm still hoping for feedback on this... Thanks, Franklin (24 years ago, 29-May-02, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: CMDLINE meta-statement
|
|
(...) ("(URL) CMDLINE meta-statement is a way of permitting a file's author to *document* certain run-time commands which can be considered as default or required for the file in question. For example, most minifig faces are printed on yellow (...) (24 years ago, 29-May-02, to lugnet.cad.dat.parts, lugnet.cad.dev)
|
| |
| | Re: Minifig Head with Messy Ice Planet Hair Pattern
|
|
(...) No, I won't. But it was to late for me yesterday. (...) You're right, I have this set. It's "FORT LEGORADO", so I know what to do after the IP2002 Parts. What does CMDLINE mean? I haven't understand until now. CU Bernd (24 years ago, 28-May-02, to lugnet.cad.dat.parts)
|
