 | | Re: Rubber belts modelling utility
|
|
(...) I was imprecise. I was thinking of pulleys that are rotated 90º in relation to each other. It would look something like this in plan. (sorry for this bad diagram) Ox- "O" = big pulley "x" = belt "-" = pulley rotated 90º Or here's a good (...) (25 years ago, 26-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Rubber belts modelling utility
|
|
Hi Kyle, (...) ??? For pulleys in the horizontal plane it is easy to rotate the generated rubber belt 90°. Or do you mean something different ? Philo www.philohome.com (25 years ago, 26-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Subpart 3811S02.DAT Island pattern for Baseplate 32 x 32 [DAT]
|
|
Here's the subpart for the large Island baseplate. 0 ~Subpart for Baseplate 32 x 32 with Island Pattern 0 Name: 3811S02.DAT 0 Author: Andrew Westrate 4 1 318 0 -2 318 0 -52 274 0 -53 274 0 -2 4 1 274 0 -2 274 0 -53 256 0 -57 256 0 -2 4 1 256 0 -2 (...) (25 years ago, 26-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | New Part 3811 Baseplate 32 x 32 with Island pattern [DAT]
|
|
Since I didn't have too much difficulty with the similar 16x16 baseplate, I've created the 32x32 Island baseplate from the Pirates line. Since there is already a pattern 01 for this part, I assumed this one could be 02, and named the sub-part (...) (25 years ago, 26-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: 3867 Baseplate 16 x 16 with Island Pattern [DAT]
|
|
I've updated the part to have the blue parts hard-coded blue, and the remainder of the piece (the sides & bottom) grey. Andy 0 Baseplate 16 x 16 with Island Pattern 0 Name: 3867P01.DAT 0 Author: Andrew Westrate 0 Unofficial Part 0 CATEGORY Baseplate (...) (25 years ago, 26-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Rubber belts modelling
|
|
(...) That's real cool! Will you be considering the possibility of pulleys that are rotated 90º? (...) (25 years ago, 26-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Subfiles - Question
|
|
(...) I think using subparts makes sense in this case. Steve (25 years ago, 25-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part: 30621.dat - Brick 12 x 2 with lots of stuff
|
|
(...) I noticed that -- I saw it on the Parts Tracker. :) Any chance you could rotate it 90 degrees? For a long time, we've had a mix of orientation for asymmetric(al?) parts -- some were placed longways on the X-axis, some along the Z-axis. Awhile (...) (25 years ago, 25-Mar-02, to lugnet.cad.dat.parts)
|
| |
| | Re: Rubber belts modelling
|
|
I just uploaded a Rubber Belt Generator utility, that creates DAT files for rubber belts taut between two pulleys. The rubber belt generated can have a square section or a round one, using cylinder primitive. This utility is available from (URL) (...) (25 years ago, 25-Mar-02, to lugnet.cad.dat.parts, lugnet.robotics, lugnet.technic)
|
| |
| | Re: Subfiles - Question
|
|
(...) That's what i've done this evening. I splitted the main file into one new subfile (32087s02.dat witch re-use the 2865s04.dat file)and the mainfile (32087_mainfile.dat). I couldn't add the small center track pieces too the 32087s02.dat file due (...) (25 years ago, 24-Mar-02, to lugnet.cad.dat.parts)
|
