Subject:
|
Re: Lpub Dual Callout
|
Newsgroups:
|
lugnet.cad
|
Date:
|
Tue, 31 May 2005 14:58:37 GMT
|
Viewed:
|
1087 times
|
| |
|
|
In lugnet.cad, Philippe Hurbain wrote:
> I want to use the same callout twice in the same step. I tried to use the
> following code (and variations...), but when generating layouts Lpub complains
> that a file (MPDname_0_04_co_1.png) is missing. And after that one of the bars
> is missing in the CSI (but the PLI is correct).
>
> What should I do ?
Hi Philo,
I've uploaded a DAT file to brickshelf that uses multiple pointers with a
single callout, and a bunch of other tests. I made this file at the
recommendation of Mike Walsh. I use it to test LPub.
I'm updating the documentation to indicate that LPub really only deals with
one "add part" record between CALLOUT BEGIN/END.
You should be able to place each part between a BEGIN/END.
LPub does not have pointers affect part count, but I think it should. If you
have one callout and two arrows, this should show up as two parts in the PLI and
BOM. The other solution would be to allow more than one "add part" line between
BEGIN/END, as long as they are the same part type (submodel type). I think I
like the second solution better.
Feedback?
Kevin
>
> Philo
>
> 0 LPUB CALLOUT PLACEMENT TOP_RIGHT PAGE
> 0 LPUB CALLOUT BEGIN
> 0 LPUB CALLOUT POINTER LEFT 0.2 0.77 0.1
> 0 LPUB CALLOUT POINTER LEFT 0.3 1 0.19
> 1 0 -160 0 0 1 0 0 0 1 0 0 0 1 bar.ldr
> 1 0 -20 0 0 1 0 0 0 1 0 0 0 1 bar.ldr
> 0 LPUB CALLOUT END
> 0 LPUB MULTI_STEP END
>
> (snip)
>
> 0 FILE bar.ldr
> 1 8 0 -117.68 57.59 0 0 -1 0 -140 0 -1 0 0 77.DAT
> 1 7 0 -117.68 57.59 0 -0 1 1 -0 -0 0 1 0 4274.DAT
> 0 STEP
> 1 0 0 -127.68 37.59 1 -0 -0 -0 0 -1 0 1 0 6536.DAT
> 0 STEP
> 1 0 0 -147.68 57.59 -0 -0 -1 1 0 -0 0 -1 0 6536.DAT
> 1 0 0 -187.68 57.59 -0 -0 -1 1 0 -0 0 -1 0 6536.DAT
> 1 0 0 -167.68 57.59 -0 -0 -1 1 0 -0 0 -1 0 6536.DAT
> 0
|
|
Message has 1 Reply:
 | | Re: Lpub Dual Callout
|
| (...) This one: (URL) ? Thanks... nothing better than an axample! (...) I do too (the multi pointer could have other uses) There might be a third solution, something like the "inverse" of LPUB PLI BEGIN IGN that would allow to add parts to the PLI (...) (19 years ago, 31-May-05, to lugnet.cad)
|
Message is in Reply To:
| | Lpub Dual Callout [DAT]
|
| I want to use the same callout twice in the same step. I tried to use the following code (and variations...), but when generating layouts Lpub complains that a file (MPDname_0_04_co_1.png) is missing. And after that one of the bars is missing in the (...) (19 years ago, 31-May-05, to lugnet.cad)
|
8 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
