Subject:
|
Re: New parts - Aquanaut Door and Door Frame
|
Newsgroups:
|
lugnet.cad.dat.parts, lugnet.cad
|
Date:
|
Wed, 21 May 2003 10:25:48 GMT
|
Viewed:
|
100 times
|
| |
|
|
In lugnet.cad.dat.parts, Marek Idec writes:
> Hello,
>
> I've just sent to Parts Tracker my two new parts. Please review them and give
> me your feedback.
>
> 2662.dat - Door Frame 2 x 10 x 12
> http://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/2662.dat
> and subpart
> http://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/s/2662s.dat
>
> 2596.dat - Door 1 x 9 x 11
> http://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/2596.dat
> and subpart
> http://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/s/2596s.dat
Hi, All,
I have corrected those parts according to precious remarks of Paul Easter.
Thanks a lot, Paul.
At the begining I didn't know what is wrong with studs in 2596.dat. When I
replaced official studs with studs of Paul with LEGO logo then I immediately
knew what is wrong. Theye were rotated and two of them even mirrored.
There is still question about orientation of Door Frame. To be more specific
about "level 0". Before I created my part I looked at similar parts like arches
6005.dat and 6060.dat. The have "level 0" on the most top plane of the part. I
did the same. Paul suggests the plane where the most to studs are located to be
"level 0" plane. What is your opinion?
Paul, I'm not sure if I have understood well your remarks about spaces in
header lines. To be sure that multiple spaces are not shrinked into one space
in my examples below I replaced spaces with underscores.
My header line initially looked like this (except underscores of course)
"0_Door_1_x_9_x_11" with singe spaces between numbers, words and letters. I
understood suggestion of Paul that there should be additional space in front of
single digit numbers. Should it look like this "0_Door__1_x_9_x_11" or even
"0_Door__1_x__9_x_11", Paul? To be honest I've never heard about that rule, so
please correct me if I misunderstood you.
I also corrected names of sub-parts. All files are available in PT
http://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/2662.dat
http://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/s/2662s01.dat
http://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/2596.dat
http://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/s/2596s01.dat
Please review them.
Marek Idec
|
|
Message has 1 Reply:
 | | Re: New parts - Aquanaut Door and Door Frame
|
| (...) Has no one responded to this yet? My understanding is that the spacing is purely to make part names alphabetize properly, so that, for example, Brick 1 x 2 sorts before Brick 1 x 16. I think the last example above is correct, but I'm sure that (...) (21 years ago, 5-Jun-03, to lugnet.cad.dat.parts)
|
Message is in Reply To:
5 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
