 | | Re: Peeron_to_MLCad
|
|
(...) Hi Scott If I decide to write a new version of Peeron_to_MLCad I will take note of your suggestions. I am writing to you in private on technical aspects related to programming. (15 years ago, 11-May-09, to lugnet.cad.dev)
|
| |
| | Re: LDraw.org 2009-01 Parts Update Now Available
|
|
(...) This is fantastically fabulous news! LDraw lives! Thank you so much. Allen (15 years ago, 11-May-09, to lugnet.cad, FTX)
|
| |
| | Re: Peeron_to_MLCad
|
|
Now that I've had a chance to use Peeron_to_MLCAD, I must say again, excellent work. After getting everything setup, it was fun 'building' the model in MLCAD. The tutorial was great and very necessary, as I was overwhelmed by all of the buttons and (...) (15 years ago, 9-May-09, to lugnet.cad.dev)
|
| |
| | Updated Unofficial parts pack for LeoCAD
|
|
The welcomed LDraw 2009-01 parts update rendered my previous unofficial parts pack obsolete (it needed an update anyway!). So I have prepared an updated parts pack containing all LDraw unofficial parts available as of May 8, 2009. This parts pack is (...) (15 years ago, 9-May-09, to lugnet.cad.leocad)
|
| |
| | Re: 57587.dat origin
|
|
(...) Interesting... I'm agreeing with you, as it seems other dome parts have their top pointing upwards so I shall do it this way. Thank you. (15 years ago, 9-May-09, to lugnet.cad.dat.parts, FTX)
|
| |
| | Re: MLCAD ColorManager 2.0
|
|
Looks like I had a couple of oversights and improvements that I needed to make. A big thanks to Alex Taylor for finding them. The Windows executable and C++ source code have been updated for the following improvements / fixes: faster detection of no (...) (15 years ago, 9-May-09, to lugnet.cad)
|
| |
| | Re: 57587.dat origin
|
|
(...) I would rotate that part, so it is easier to identify this part as a dome. Then I think the top should be at Y=0. I have already send a manipulated version of your mpd file to your address. cu mikeheide (15 years ago, 8-May-09, to lugnet.cad.dat.parts, FTX)
|
| |
| | 57587.dat origin
|
|
Hello all, I have recently been working on (URL).dat, "Technic Cylinder 6 x 6 x 4 with Dome Top" (though I have it here titled as "Technic Dome 7 x 7 x 5" because IMHO it's more like a dome than a cylinder). I've noticed the part origin is a problem (...) (15 years ago, 8-May-09, to lugnet.cad.dat.parts, FTX)
|
| |
| | DATHeader UPDATE (1.3.0)
|
|
DATHeader Version 1.3.0 is now available. Two new features are added. DATHeader will now care about leading spaces in front of one digit numbers. DATHeader check for the use of 'c' or 'd' in the filename if parttype 'Shortcut' is used. You can now (...) (15 years ago, 8-May-09, to lugnet.cad)
|
| |
| | Re: LDraw.org 2009-01 Parts Update Now Available
|
|
(...) Yes. I have seen and installed it. My PC was ready for a complete re-intall anyway :-) Jaco (15 years ago, 8-May-09, to lugnet.cad)
|
