To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.cadOpen lugnet.cad in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 CAD / *43776 (-10)
  Re: LPub4.0.0.1 available
 
(...) You missed a difference on Page 2. In the bottom part, the green arrows are shown in the 4.0.0.1 version, and not in the other version. (...) And round light grey plate 1x1 is not shown either. --Travis (16 years ago, 29-Sep-08, to lugnet.cad)
 
  Re: LPub4.0.0.1 available
 
(...) I am looking forward to the results, as I am due to deliver building instructions for a project I am working on. I have sent you some personal E-mails about this too. Once again, I thank _you_ for all you effords in creating LPub. (16 years ago, 29-Sep-08, to lugnet.cad)
 
  Re: Slope Brick 1x1
 
Right. So who is to change the name then? Peeron or LDraw? (16 years ago, 29-Sep-08, to lugnet.cad, lugnet.off-topic.geek)
 
  Re: Slope Brick 1x1
 
(...) But if you use the part properly* it's 31 degrees. The 45 slope is named for its face slope rather than its total slope. Tim * And by properly I, of course, mean use a heap of offsetting to make them all line up ;) (16 years ago, 29-Sep-08, to lugnet.cad, lugnet.off-topic.geek)
 
  Re: LPub4.0.0.1 available
 
(...) Jaco, Thanks for your detailed analysis complete with MPD to allow recreation. I will take if rom here and fix the LPub bugs. Kevin (16 years ago, 29-Sep-08, to lugnet.cad)
 
  Re: LPub4.0.0.1 available
 
(...) OK, while testing and playing around with LPub 4 I tried some new techniques I've come up with. I've recreated the "exact" instructions for set 4491. (URL) the same file in LPub 4.0.0.0 and 4.0.0.1 gives different outputs. I've uploaded the (...) (16 years ago, 29-Sep-08, to lugnet.cad)
 
  Re: Slope Brick 1x1
 
(...) Why does the follow-up go to the Robotics group? This is a CAD / LDraw issue, so it should be lugnet.cad.dat.parts. (My mistake in the first place to post it to lugnet.cad ;-) (16 years ago, 29-Sep-08, to lugnet.cad)
 
  Re: New FastRad Tutorial
 
(...) Very nice! Thanks! (16 years ago, 26-Sep-08, to lugnet.cad.ray, FTX)
 
  Re: Slope Brick 1x1
 
(...) Hmm. Is there some reason you couldn't just jump right to using Tan? Tan(theta) = opposite/adjacent (16 years ago, 27-Sep-08, to lugnet.cad)
 
  Re: Slope Brick 1x1
 
(...) The part file has the dimensions needed to answer this question. The triangles on the sides tell you the width and height of the end. From there you can calculate the length of the hypotenuse. h = sqrt(w*w+h*h) the sin of the angle is (...) (16 years ago, 27-Sep-08, to lugnet.cad)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR