 | | Re: Callout in LPub [DAT]
|
|
(...) OK! Nearly there: (URL) to eleminate the arrows in the assem (due to ghosting) and get rid of step 2 in the call out. Also the pointer is missing (something wrong with the code?) Here is the DAT code of the entire model: 0 FILE 1088.ldr 0 Set (...) (19 years ago, 31-May-05, to lugnet.cad)
|
| |
| | Re: Orientation in PLI and BOM
|
|
(...) Right. I did so, but the frustrating thing was that it didn't work. No matter what I did the part kept displaying the same way. Until ofcourse I deleted the image from the parts folder and did a new render... :-) Thanks again, Kevin! Jaco (19 years ago, 31-May-05, to lugnet.cad)
|
| |
| | Re: Orientation in PLI and BOM
|
|
(...) This is a tough situation Jacko. If you look at LEGO PLI's you'll notice the orientation of a technic brick. The left end of the brick is rendered lower than the right end of the brick. Now look at the orientation of the same brick in the (...) (19 years ago, 30-May-05, to lugnet.cad)
|
| |
| | Orientation in PLI and BOM [DAT]
|
|
Though I added part 3829 Car Steering Wheel to the ORIENTATION.LDR file in the extra's folder of LPub, the part shows up wrong in the PLI and BOM: (URL) this a bug? Or did I do something wrong? I added it like this: 1 0 0 0 0 0 0 1 0 1 0 -1 0 0 (...) (19 years ago, 30-May-05, to lugnet.cad)
|
| |
| | Re: Callout in LPub
|
|
(...) 0 // Idefinty part calledoutmodel.ldr 0 LPUB CALLOUT BEGIN 0 // Place the callout centered above the assembly 0 LPUB CALLOUT PLACEMENT TOP CENTER ASSEM 0 // Draw a pointer from right edge of callout to upper right of ASSEM 0 LPUB CALLOUT (...) (19 years ago, 30-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
(...) OK... Note that unfortunately I still don't have that updated documentation (installer problem, see (URL) In LPub traditional form (which is annoying), the "mistake" of using ASSEM, is (...) Yes, that deafening silence is annoying. After (...) (19 years ago, 30-May-05, to lugnet.cad)
|
| |
| | Parts substitution [DAT]
|
|
Some parts that consist of more subparts must be drawn as one part in the PLI. LPub has a command for this I used: 0 LPUB PLI BEGIN SUB hinge.ldr 1 0 0 -40 80 1 0 0 0 1 0 0 0 1 hinge.ldr 0 LPUB PLI END SUB I created the file inside the MPD file: 0 (...) (19 years ago, 30-May-05, to lugnet.cad)
|
| |
| | Callout in LPub
|
|
Hi all, Though I am getting more and more good results from making building instructions using LPub I still have some questions. I know I posted a lot of questions already, but there are some new. Since I lost track of replies and answers, I decided (...) (19 years ago, 30-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub [DAT]
|
|
(...) I think I did this, but the picture I get is this: (URL) parts at all for the hinge? With the code like this: 0 STEP 1 1 -30 -16 70 0 0 1 0 1 0 -1 0 0 4085C.DAT 1 1 30 -16 70 0 0 -1 0 1 0 1 0 0 4085C.DAT 1 1 0 -16 -110 1 0 0 0 1 0 0 0 1 (...) (19 years ago, 29-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
(...) Philo, In my code and the documentation I posted yesterday, STEP_NUMBER can only be placed relative to PLI or PAGE. It currently cannot be placed relative to the ASSEM image. Therefore you cannot do what you want. In LPub traditional form (...) (19 years ago, 29-May-05, to lugnet.cad)
|
