| | Re: Questions about LPub
|
|
(...) There are a couple of things that throw LPub off and I'm trying to figure out how to make it "do the right thing". You have: ROTSTEP part part part STEP ROTSTEP END This is equivalent to: part part part ROTSTEP ROTSTEP END LPub ignores STEP (...) (19 years ago, 28-May-05, to lugnet.cad)
|
|
| | Re: Questions about LPub
|
|
(...) I got this one fixed: it was caused by the "0 ROTSTEP END" at the end of the subfile (actually a plain 0 STEP at the end also brings on this behaviour) Philo (19 years ago, 28-May-05, to lugnet.cad)
|
|
| | ldraw part fro #32467
|
|
Does anyone have a .dat / ldraw file for part 32467 Yellow Electric Computer Speed as in set: (URL) (19 years ago, 28-May-05, to lugnet.cad)
|
|
| | Re: Questions about LPub
|
|
Hello Kevin, (...) I have a similar problem: pack_callout: accumulated width too large but AFAIK it is not a recursive call problem... The mpd file is here (the problem occurs when generating layout 5) (URL) purpose of the callout (and tentative (...) (19 years ago, 28-May-05, to lugnet.cad)
|
|
| | Re: LPub 2.3.0.7
|
|
In lugnet.cad, Philippe Hurbain wrote: <snip> (...) Fixed. Released. (...) Added. Not released. (...) Documentation made available. Kevin (19 years ago, 28-May-05, to lugnet.cad)
|
|
| | Re: Questions about LPub
|
|
(...) Jacko, This is because hinge.ldr references itself in a LPUB PLI BEGIN SUB hinge.ldr. I removed the offending LPUB PLI BEGIN SUB/LPUB PLI END. I copied the parts listed in hinge.ldr to the places you used hinge.ldr. I then surrounded those (...) (19 years ago, 28-May-05, to lugnet.cad)
|
|
| | Re: Questions about LPub [DAT]
|
|
(...) I found and fixed a bug in PLI. (...) It contains this: 0 Torso & arms 0 Name: torsoarms.ldr 0 Author: Jaco van der Molen 0 Unofficial Model 0 ROTATION CENTER 0 0 0 1 "Custom" 0 ROTATION CONFIG 0 0 0 LPUB PLI BEGIN SUB torsoarms.ldr 1 1 0 0 0 (...) (19 years ago, 28-May-05, to lugnet.cad)
|
|
| | Re: Questions about LPub
|
|
OK. I am getting there :-) (...) This was a succes, though I do not have a pointer yet: (URL) further, I get an error: pack_callout: accumulated height too large And: layout_page: Failed to open file LPub\Layout\truck_0_05_co_0.png for reading Then, (...) (19 years ago, 27-May-05, to lugnet.cad)
|
|
| | Re: Questions about LPub
|
|
How can I get something like this on the first page of the instructions? (URL) (19 years ago, 27-May-05, to lugnet.cad)
|
|
| | Re: Questions about LPub
|
|
(...) I am getting this error: Cannot find user part image C:\LDRAW\MODELS\MISC...s_c.PNG_c. Did you create create construction images? What could be wrong? I have posted my MPD file on Brickshelf here: (URL) (19 years ago, 27-May-05, to lugnet.cad)
|