 | | Re: MLCad: maximum filesize?
|
|
Hello Maarten, "Maarten Steurbaut" <maarten.steurbaut@skynet.be> schrieb im Newsbeitrag news:HpsA05.1J9@lugnet.com... (...) only (...) it (...) are (...) There are nearly no software limits, meaning you can have as many parts as you like. However (...) (21 years ago, 13-Dec-03, to lugnet.cad)
|
| |
| | Re: MLCad: maximum filesize?
|
|
I was clever enough to use submodels right from the start (each containing 2.500 to 3.000 pieces). Every now and than I have to take a look at the result just to check if I am still doing allright, and this is were I loose time (approx. 15 seconds (...) (21 years ago, 13-Dec-03, to lugnet.cad)
|
| |
| | Re: Any Stinkers here?
|
|
Hejo, Yes, it was I. I don't read the groups here that often, sorry. We got in contact and I sent one of my povray files that contain the mentioned settings. I must however give all credits to Jeroen de Haan. All I know I learned from him and his (...) (21 years ago, 13-Dec-03, to lugnet.cad.ray, lugnet.general)
|
| |
| | Re: Wheel 11 x 8 with Center Groove/Tyre 17.5 x 6 with Shallow Staggered Treads?
|
|
Seems not to be the case. If I make a crack at them where do I get x-numbers for them? (...) (21 years ago, 13-Dec-03, to lugnet.cad.dat.parts, FTX)
|
| |
| | Re: Rare parts: Small switch yard engine
|
|
Sorry for bringing up an old topic again, (...) The rare trainbase seems to be the prototype for the trainbase, which is listed as x902c01 on peeron. Recently I received two of these parts and I have just finished an LDraw part, posted in message (...) (21 years ago, 13-Dec-03, to lugnet.trains, lugnet.cad)
|
| |
| | Re: MLCad: maximum filesize?
|
|
(...) Mayby you could use submodels (smaller portions of your sculpture) to avoid MLCad getting very slow. When you want your final result as one straight ldr-file you can have all your submodels inlined when they're finished. Niels (21 years ago, 13-Dec-03, to lugnet.cad)
|
| |
| | Re: MLCad: maximum filesize?
|
|
(...) To think I considered myself crazy when I modelled the ISD. ;-) (...) Not that I'm aware of. I assume Michael uses file pointers so file size shouldn't be an issue. (...) Yes and no. No in that there is no limitation in MLCad (although Michael (...) (21 years ago, 13-Dec-03, to lugnet.cad)
|
| |
| | New part: Train Base 6 x 22 with Motor Cutout Type I [DAT]
|
|
0 Train Base 6 x 22 with Motor Cutout Type I 0 Name: Untitled1 0 Author: Niels Karsdorp <nkp@dds.nl> 0 Unofficial Element 0 BFC CERTIFY CW 0 --Boxes and rectangles 1 16 0 4 -20 0 0 220 4 0 0 0 -40 0 box3u2p.dat 1 16 0 4 20 0 0 220 4 0 0 0 40 0 (...) (21 years ago, 12-Dec-03, to lugnet.cad)
|
| |
| | Re: Any Stinkers here?
|
|
Hi all, According to the webmaster the server was hacked and therefore down. It is up again, although I can't access the index page but you go there direct: (URL) about this all, Jeroen "Dave Schuler" <orrex@excite.com> wrote in message (...) (21 years ago, 12-Dec-03, to lugnet.cad.ray, lugnet.general)
|
| |
| | MLCad: maximum filesize?
|
|
Hi all, I am creating a very large sculpture - a virtual sculpture of course - only using plates, jumper plates and tiles. I am nearly halfway the project and it has already approximately 30.000 pieces (filesize is 1.2 MB). Things are slowing down a (...) (21 years ago, 12-Dec-03, to lugnet.cad.mlcad, FTX)
|
