 | | Re: My first rendering of a CAD-model.....
|
|
(...) I wish my newbie products turned out this wonderful... With a bit of tuning your BR24 train would make a serious chance in the model of the month competition at LDRAW.ORG (if that's back up yet, Tim?) Might I suggest you take a look at Jeroen (...) (21 years ago, 23-May-03, to lugnet.cad)
|
| |
| | Re: My first rendering of a CAD-model.....
|
|
In lugnet.cad, Stefan van Zwam writes: Hi Stefan! I have had some other plans with that special wheel in red: (...) number at hand, but the alternative model is a dragster and there are these red wheels used.... (...) None of them so far... :-(( But (...) (21 years ago, 23-May-03, to lugnet.cad, lugnet.trains)
|
| |
| | Mac Brick CAD (cocoa version) - New Development Release
|
|
Mac Brick CAD (MBC) in cocoa - formally known as Mac Lego Modeller. After some delay, here is an update to my Cocoa release. As before, this is for test pilots and lacks lots of features (use the Carbon/Classic versions for better features) But that (...) (21 years ago, 23-May-03, to lugnet.cad.dev.mac)
|
| |
| | Re: My first rendering of a CAD-model.....
|
|
(...) Nope, I can't make that decision, but I did direct you to the Parts Tracker in an email I just sent :-) -Tim (21 years ago, 23-May-03, to lugnet.cad)
|
| |
| | Re: My first rendering of a CAD-model.....
|
|
(...) Hi Jan-Albert, I am not sure, how parts are submitted to the LDraw officials - I am a bloody newbie in CAD. I wrote to Tim Courney and hope he is one of the persons, who can decide if this file is good enough for the official Ldraw dat (...) (21 years ago, 23-May-03, to lugnet.cad)
|
| |
| | Re: Symmetries other than 16 and 48?
|
|
(...) For parts with unusual symmetries, I would suggest either (or both): 1. Make a subfile in parts\s with 1 segment of the part, then use that subfile as many times as you need. 2. Find a higher-level symmetry that is common with 16 or 48 (...) (21 years ago, 23-May-03, to lugnet.cad.dev)
|
| |
| | [Parts Tracker] Notes for Admins
|
|
Just a quick note for authors & reviewers on the Parts Tracker -- if you need an admin to address something, please email parts@ldraw.org about it -- if you just leave a comment in a review, the admins will only pick up on it by chance. Actually, (...) (21 years ago, 23-May-03, to lugnet.cad.dev)
|
| |
| | LeoCAM BETA RELEASE !!!
|
|
Hi all: After a couple of delays, I'm extremely proud to announce the release of the newer version of LeoCAM, the beta version. With this new implementation, you'll able to snap parts effortlessly just by clicking on their connectors. You'll even be (...) (21 years ago, 23-May-03, to lugnet.cad)
|
| |
| | Re: Is anyone making part 44224.dat?
|
|
The mating part is refered to as 44225 on both Peeron and Bricklink... Philo (...) (21 years ago, 23-May-03, to lugnet.cad.dev, lugnet.cad.dat.parts)
|
| |
| | Difficulties in LPub
|
|
Hi Kevin (and everyone else ofcourse), After a few trials and errors, I finally managed to get the parts in the Part List Images at the same scale. It turns out that I had to set the minimum distance to 50000 (!). Is this because a plate of 6x16 is (...) (21 years ago, 23-May-03, to lugnet.cad.ray)
|
