 | | Re: New Part - 2527 Plate? 2 x 4 cannon base
|
|
(...) Is it necessary to specify a length 'n' if it's an accessory? That is, does the Minifig Tool Knife (whatever it's called specifically) mention a length? I'm just curious, but it seems that unless there's a length difference between shooting (...) (24 years ago, 13-Dec-00, to lugnet.cad.dat.parts)
|
| |
| | "POV-RAY"-friendly minifig coins
|
|
Here are the URLs for the updated DAT files. The "10"-mark coin: "(URL) The "20"-mark coin: "(URL) The "30"-mark coin: "(URL) The "40"-mark coin: "(URL) Thanks, Franklin ===== Franklin Cain (and please do *not* call me "Frank" ;-) fwcain@yahoo.com | (...) (24 years ago, 13-Dec-00, to lugnet.cad.ray, lugnet.cad.dat.parts)
|
| |
| | Re: new lego-cad part: x474.dat, "Arm Piece with Towball and Stud"
|
|
(...) I used the code for 30082.dat, "Arm Piece with Towball and Clip", as a startnig point. Inside that DAT file, there is a dome (4-8sphe.dat), used for the "front" half of the towball, that has a diameter of _14_, not 16. Franklin (24 years ago, 13-Dec-00, to lugnet.cad.dat.parts)
|
| |
| | Re: Visor??
|
|
(...) What would we call that? "Minifig Helmet Visor Blinders w/ Antenna"? "Minifig Helmet Visor Ice Planet"? Franklin (24 years ago, 13-Dec-00, to lugnet.cad.dat.parts)
|
| |
| | Re: Visor??
|
|
(...) What would we call that? "Minifig Helmet Visor Blinders w/ Antenna"? "Minifig Helmet Visor Ice Planet"? Franklin (24 years ago, 13-Dec-00, to lugnet.cad.dat.parts)
|
| |
| | Re: new lego-cad part: x474.dat, "Arm Piece with Towball and Stud"
|
|
(...) Looks good. Has TLC made variations on this part? Seems like I recall discussion of an older and a newer version, but I don't remember clearly now. (...) I'm not understanding where you're coming from with this comment. All the towball parts I (...) (24 years ago, 13-Dec-00, to lugnet.cad.dat.parts)
|
| |
| | Re: New Part - 2527 Plate? 2 x 4 cannon base
|
|
(...) Very nice job on these parts! I think I'd name the cannon parts as: 2527.DAT Minifig Cannon 2 x 4 Base x518.DAT Minifig Cannon 2 x n Non-Shooting Sorry, I don't have a cannon handy for measurement -- replace the 'n' with the proper length. (...) (24 years ago, 13-Dec-00, to lugnet.cad.dat.parts)
|
| |
| | Re: endparts
|
|
Could you center them around the Y-axis? Also, I don't now if I schould make the airtubes hollow or not, some purist might say yes, but you would never see it and it would take up twice as much space. Any suggestions? thanks a lot, koen. John (...) (24 years ago, 13-Dec-00, to lugnet.cad.dat.parts)
|
| |
| | RE: L3PAO update (v 1.3)
|
|
(...) URL? --Bram Bram Lambrecht bram@cwru.edu (URL) (24 years ago, 13-Dec-00, to lugnet.cad.dev)
|
| |
| | L3PAO update (v 1.3)
|
|
When using L3PAO to do the Beretta this week, I noticed a few issues here and there, so I compiled an update. (URL) 1.3 ---...--- Fixed yet another error in the command line generator. If the path to l3p was the same as the path to L3PAO, it was (...) (24 years ago, 13-Dec-00, to lugnet.cad.dev)
|
