 | | Re: LEGO grandfather clock
|
|
(...) Eric, Once again... Amazing! I am at a loss for words. Eric Kingsley The New England LEGO Users Group (URL) My Creations At: (URL) (25 years ago, 20-Jan-00, to lugnet.general, lugnet.build)
|
| |
| | Re: LEGO grandfather clock
|
|
Wow! Now you need to build a LEGO mouse running up it. I would love to see the gearing mechanisms you built into that thing. Perhaps I could build one as well and put it into my LEGO train room. I especially like the picture of Parker Posey as (...) (25 years ago, 20-Jan-00, to lugnet.general, lugnet.build)
|
| |
| | LEGO grandfather clock
|
|
Folks, All had been quiet with my LEGO sculpting recently, but now I offer my grandest creation to date... [drumroll]... (URL) tock, eric (25 years ago, 20-Jan-00, to lugnet.general, lugnet.build)
|
| |
| | Re: System Axles
|
|
(...) vehicles (...) with (...) I'd been meaning to email you personally about this, but lately I've been too busy collecting free, informative pamphlets on how to lower the dust mite count in my home. -Tom McD. when replying, off-camera, Squiddley (...) (25 years ago, 20-Jan-00, to lugnet.build, lugnet.off-topic.fun)
|
| |
| | Re: Yellow inverted slopes?
|
|
(...) There were two of the inverted extreme slopes in set #1896, Trauma Team. And 4 of non-inverted 1x2x3 yellow slopes, too. Source: Tim Vattima's set/piece inventory cross-reference at (URL). Thanks, Tim! I always meant to buy that set, but never (...) (25 years ago, 20-Jan-00, to lugnet.build)
|
| |
| | Re: Pythagorean Triads and Almost-Triads
|
|
John J. Ladasky Jr. wrote in message <38814540.ED2D820E@m...ja.com>... (...) John, how could I possibly have forgotten that? ;-) (...) Here we go again..... :-) I think I don't. You see, my rule of thumb is that the walls that form the sides of the (...) (25 years ago, 21-Jan-00, to lugnet.build)
|
| |
| | Re: Container grabber
|
|
(...) Please do show us some detailed photos. The overhead crane is in need of a design impovement to make it useful (able to pick up piggyback trailers). Jim --- (25 years ago, 20-Jan-00, to lugnet.build, lugnet.trains)
|
| |
| | Re: Container grabber
|
|
The grabber I made is designed to lift my 6 wide piggyback trailers as seen on my webpage. (it will also lift 4 wide trailers). It uses L shaped 2x2 plates in the 4 holes of the red grabber. Attached to the outside of the plates is a 8x1 block. On (...) (25 years ago, 20-Jan-00, to lugnet.build, lugnet.trains)
|
| |
| | Re: 8 Wide train hopper
|
|
(...) Disclaimer, this is not exactly mine, it's a reasonable facsimile that Mike put together by being very observant. I'm OK with that as long as it's disclaimed. :-) (...) (25 years ago, 20-Jan-00, to lugnet.trains, lugnet.build, lugnet.loc.us.ca.sf)
|
| |
| | Re: Container grabber
|
|
(...) I just built the grabber. I extended it by 6x1 & added a 4x1 plate to the bottom inside. The only problem is that last year (99) I started to build trailer 6x?? so now I'll have to build 4x?? trailers for small trucks & 6x?? for large trucks. (...) (25 years ago, 20-Jan-00, to lugnet.books, lugnet.build, lugnet.trains)
|
