 | | Re: Partsref is Moving to LUGNET
|
|
(...) I'm going to need to keep a vanilla installation, just for partsref generation. It's too tempting to make minor edits to part files in my regular installation. And, if I'm going to have two copies of LDraw, I'd rather have "working" and (...) (25 years ago, 3-Dec-99, to lugnet.cad.dev, lugnet.db.brictionary, lugnet.cad.ray)
|
| |
| | RE: Interested in older catalogs
|
|
Hi, We may have some older duplicates. What years are you looking for? m (...) (25 years ago, 2-Dec-99, to lugnet.loc.us.ca.sf)
|
| |
| | Re: TRU stuff shipped yet? Anyproblems?
|
|
TRU probably did it, just because KB and everyone else was doing it, not to be creative on their own. As these coupons are used (and somewhat abused), I think we will see fewer and fewer of them. Of course, if the few that 'take advantage' of them (...) (25 years ago, 3-Dec-99, to lugnet.market.shopping)
|
| |
| | Re: TRU stuff shipped yet? Anyproblems?
|
|
(...) Actually, you're probably wrong about this. If you looked at the little blue line above their page you would have seen something like "Welcome McDonalds Winner" or something like that. MANY of these offers are urls or coupon codes that are (...) (25 years ago, 3-Dec-99, to lugnet.market.shopping)
|
| |
| | New usefull feature in eBay
|
|
The other day I discovered a new feature in eBay. eBay regulars will recall that you used to be able to see your maximum bid on your "My eBay page". While that has not yet returned, if you bid against yourself, and don't increase the bid, you now (...) (25 years ago, 3-Dec-99, to lugnet.market.auction)
|
| |
| | Re: Partsref is Moving to LUGNET
|
|
[should've snipped the ng list, but I didn't--couldn't decide which to keep/exclude] (...) So, as both the new Keeper of the LDraw Library and the Keeper of the Partsref Pages, I could build a make, and apply it everytime I get new candidate files (...) (25 years ago, 3-Dec-99, to lugnet.cad.dev, lugnet.db.brictionary, lugnet.cad.ray)
|
| |
| | Re: pcode for 20x4 LCD
|
|
(...) I think that i can help you. I do have the data sheets of the 'OPTREX DOT MATRIX LCD MODULE' It contains 47 pages,but i can filter the most interesting ones out for you,especially the ones on how to program the full 80 characters + the (...) (25 years ago, 3-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Update Auction 9 Volt Train Sets
|
|
* * * Auction 9 Volt Train Sets * * * L Set Name St Bid Bidder 1 - 9v Trains Start Set - 50 min. 2 4537 Twin Tank Transport - 30 Remy Evard 3 4544 Car Transport Wagon - 25 Mark & Milissa Millere 4 4548 Speed Regulator - 20 Jan-Albert van Ree 5 4551 (...) (25 years ago, 3-Dec-99, to lugnet.market.auction)
|
| |
| | pcode for 20x4 LCD
|
|
I picked up the 20x4 LCD at bgmicro, and it works fine. I have pcode for 20x2 successfully running, simply by re-compiling with the LCD_COLS set to 20. Does anyone have the mods required to support all 4 lines of the display? It looks to be beyond (...) (25 years ago, 3-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: New part: Plate 6 x 6 x 2/3 Cross with Dome - 30303.dat
|
|
(...) Nice job, it looks good. While looking at the new tubes, I noticed another problem. There are no edges on the curved surfaces! You can see this if you look at the part in LDLite with wireframe and rotation turned on. The regular studs, and the (...) (25 years ago, 3-Dec-99, to lugnet.cad.dat.parts)
|
