| | Re: Conditional Ring primitive?
|
|
(...) That's a primitive I have been longing for... but I realized it is impossible to build: where would you put the control lines? The top control points would need to be scaled differently from bottom ones to match various cylinders/cones (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
|
| | Conditional Ring primitive?
|
|
(...) I just noticed something else while investigating a fix for the above problem. The above model could really use a circular conditional edge primitive. I would vote for x-ycedge.dat as the filename (ie 1-4cedge.dat, 4-4cedge.dat, (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
|
| | Re: Colinear Vertices
|
|
(...) I played with the settings, and I had to set the precision all the way down to 0.133 in order to get it to fully smooth. (0.125 failed to smooth properly.) (...) .005. I think I'll set the precision to .01, to hopefully give it some leeway. I (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
|
| | Another color change?
|
|
(URL) (16 years ago, 12-Dec-08, to lugnet.general, lugnet.color, FTX)
|
|
| | 1450 Class diesel
|
|
After some more tinkering I have up'ed the screenshots. (URL) it is a cross between the 1400 and 1450, but they are very similar with the main difference being the side grills. I used the dark blue grey train base as the spine, and extended it by 8 (...) (16 years ago, 12-Dec-08, to lugnet.trains)
|
|
| | Re: LETGUI new version 0.1.0.18
|
|
(...) Thanks! For the record: - Ytruder 1.2 is no longer limited to Y direction and can extrude along x, y or z directions - Intersector 1.3 has a new scaling option that improves result for small parts. Philo (16 years ago, 12-Dec-08, to lugnet.cad.dev)
|
|
| | Re: Colinear Vertices
|
|
(...) It makes sense! (...) An example, this button: (URL) I rounded condlines to 2 decimal places since I couldn't get smoothing anyway. I did more experiments, with full precision in condline it works: (URL) but after rounding to 3 dp there is no (...) (16 years ago, 12-Dec-08, to lugnet.cad)
|
|
| | LETGUI new version 0.1.0.18
|
|
A new version of LETGUI ((URL) is now available. Support for new commandline options for Ytruder1.2 and Intersector1.3 are added. Have fun! cu mikeheide (16 years ago, 12-Dec-08, to lugnet.cad.dev)
|
|
| | Re: x210c01 ChromeSilver Drill 4 x 4 x 7
|
|
(...) Welcome back! (...) I agree with Mikeheide, since the total curvature is low I think 6 cones would be more than enough! (...) Seems a good approach. As for the edge line between screw and cones, Isecalc will provide it instantly! (It would be (...) (16 years ago, 12-Dec-08, to lugnet.cad.dat.parts)
|
|
| | Re: x210c01 ChromeSilver Drill 4 x 4 x 7
|
|
(...) I do not understand correctly what you are saying. If you use a cone primitive you can stretch it in all direction. There is no need to use "about 40 cones". A maximum of 10 should do the same! You should use for this the program "cones and (...) (16 years ago, 12-Dec-08, to lugnet.cad.dat.parts)
|