 | | Re: Novità nel factory...
|
|
(...) Confermo che NON sono foto bufala. Sono modelli che fanno parte dei set e a mio avviso non sono il meglio per rappresentare i due set. Proprio ieri mi è arrivata la copia stampata di BrickJournal, la porterò domani a Zagarolo per farla vedere (...) (17 years ago, 29-Feb-08, to lugnet.org.it.itlug)
|
| |
| | Re: Novità nel factory...
|
|
sul brick journal ci sono 2 foto: (URL) mi aspettavo di meglio (sul livello delle case modulari) sempre che non siano foto-bufala :-) ciao Cristian (17 years ago, 29-Feb-08, to lugnet.org.it.itlug)
|
| |
| | Museo di Zagarolo: termine esposizione
|
|
E' incredibile come il tempo voli: sembra ieri il giorno del montaggio della mostra al Museo di Zagarolo. Ebbene oggi è l'ultimo giorno dell'esposizione e domani si smonta... E' sicuramente stata una bella esperienza e una novità assoluta per Itlug. (...) (17 years ago, 29-Feb-08, to lugnet.org.it.itlug)
|
| |
| | Re: Help writing LDraw's history
|
|
(...) That's right. I also did the Mac port of ldglite before BrickDraw3D. (17 years ago, 29-Feb-08, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: L3Lab for Mac
|
|
(...) Ahhh... Sorry for completely missing that. (...) In LDView, you zoom with either the scroll wheel, or by right (or control) clicking and dragging up and down. (On a Mac, Control click is almost always considered to be the equivalent of a right (...) (17 years ago, 29-Feb-08, to lugnet.cad.dev.mac)
|
| |
| | Re: Compass sensor with NXC
|
|
(...) I emailed Karen with the solution to her problem. This can trip you up if you aren't careful. Drawing values to the screen can confuse you if you draw over the top of an existing number without clearing the screen first. John Hansen (17 years ago, 29-Feb-08, to lugnet.robotics.nxt)
|
| |
| | Re: L3Lab for Mac
|
|
(...) Thanks! (...) Yes, I just realized I have misunderstood the Selected state in HIToolbar - only one item can be selected at any time, so I cannot use it for showing the state of the many toggles in the toolbar. Guess I'll have to change the (...) (17 years ago, 29-Feb-08, to lugnet.cad.dev.mac)
|
| |
| | Re: L3Lab for Mac
|
|
(...) Case shouldn't matter on the Mac. I don't check for P and PARTS. The prompt ("LDrawDir '%s' is not a valid directory", Path) comes if (stat(Path, &Stat) == 0 && (Stat.st_mode & S_IFDIR)) fails. So please check again... and remove the trailing (...) (17 years ago, 29-Feb-08, to lugnet.cad.dev.mac)
|
| |
| | Re: L3Lab for Mac
|
|
(...) You might check the P and PARTS directories. I switched them to lower case in the plist. I didn't try with them upper case, so I don't know if that would have worked or not. I know the error message is complaining about the main LDraw (...) (17 years ago, 29-Feb-08, to lugnet.cad.dev.mac)
|
| |
| | Re: L3Lab for Mac
|
|
(...) I double checked and I mistyped the error above. The error displays a leading slash, and so does the config file. /Users/Tim/Applicati...ith/LDraw/ is a valid directory. I added a trailing slash after LDraw/ for gits and shiggles, doesn't work (...) (17 years ago, 29-Feb-08, to lugnet.cad.dev.mac)
|
