 | | Re: Orientation in PLI and BOM
|
|
(...) This is a tough situation Jacko. If you look at LEGO PLI's you'll notice the orientation of a technic brick. The left end of the brick is rendered lower than the right end of the brick. Now look at the orientation of the same brick in the (...) (21 years ago, 30-May-05, to lugnet.cad)
|
| |
| | Re: Brickshelf going away???
|
|
(...) I seem to be getting some decidely mixed signals. Should we be migrating our files? If Brickshelf is not going away, why tell us to go away? If uploads go away, Brickshelf becomes an archive only and is effectively dead for the future. If this (...) (21 years ago, 30-May-05, to lugnet.general) !!
|
| |
| | Re: Super crane truck
|
|
(...) His three-section boom is an interesting ctration. (21 years ago, 30-May-05, to lugnet.technic)
|
| |
| | Re: 100,000 Views!!! I'm Throwing a Party on LUGNET
|
|
(...) Ohhh ... tough call there but I'll pick the (URL) long hair days"> photo. Runner-up would be the (URL) truck> because I used to build stuff like that a looong time ago! Twenty years ago this summer I was enjoying my last "childhood summer" (...) (21 years ago, 30-May-05, to lugnet.fun.party, FTX)
|
| |
| | Re: Super crane truck
|
|
(...) The 8436 F1 or the 8460 "scanner truck" are not bad either ;o) (URL) (21 years ago, 30-May-05, to lugnet.technic)
|
| |
| | Re: Lego 4032 - is Austrian the same as ANA?
|
|
(...) I would expect they are not the same but can't be sure. The corporate logos are certainly different. Austrian: (URL) (...) All Nippon Airways Ltd., I think. ( Hope that helps ) (Member of the ANA frequent travelers club because I stayed at an (...) (21 years ago, 30-May-05, to lugnet.promo)
|
| |
| | Orientation in PLI and BOM [DAT]
|
|
Though I added part 3829 Car Steering Wheel to the ORIENTATION.LDR file in the extra's folder of LPub, the part shows up wrong in the PLI and BOM: (URL) this a bug? Or did I do something wrong? I added it like this: 1 0 0 0 0 0 0 1 0 1 0 -1 0 0 (...) (21 years ago, 30-May-05, to lugnet.cad)
|
| |
| | Re: Callout in LPub
|
|
(...) 0 // Idefinty part calledoutmodel.ldr 0 LPUB CALLOUT BEGIN 0 // Place the callout centered above the assembly 0 LPUB CALLOUT PLACEMENT TOP CENTER ASSEM 0 // Draw a pointer from right edge of callout to upper right of ASSEM 0 LPUB CALLOUT (...) (21 years ago, 30-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
(...) OK... Note that unfortunately I still don't have that updated documentation (installer problem, see (URL) In LPub traditional form (which is annoying), the "mistake" of using ASSEM, is (...) Yes, that deafening silence is annoying. After (...) (21 years ago, 30-May-05, to lugnet.cad)
|
| |
| | Re: MOCpages.com status
|
|
Ok, thanks for confirmation. I was wondering about the site's status, as it's my favorite LEGO website. (Next to LUGNET, of course :) )Congrats to the happy couple! -Josh (21 years ago, 30-May-05, to lugnet.general, lugnet.publish)
|
