 | | Re: Help!! Polaroid problem!!!
|
|
When it first worked for me, I used the HB NiCd. I grounded binh and it worked. I used binh to measure like 7 inches and it worked fine too. ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Serial Communication: HB -> Win95
|
|
To answer my own question, at least partially, here is a Win95 Host program to communicate (single bytes) with the HandyBoard over a serial line: /* Win95 Visual C++ Host Code to talk to HandyBoard */ #include <conio.h> // _outp, _inp #include (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: IC stack problem
|
|
(...) The funny thing is, it doesn't complain about arrays smaller than 4x4. All values are stored correctly for an array of size 3x3. What's this 'magic' number 4 then? Jan Sipke van der veen (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: loading files with IC
|
|
In fact, that's weird.. I can't answer to that. To me, I'm pretty sure that IC would have gave me an error, like when I try to load a C program without having loaded the ICB containing the special function used by this C program. For example, i (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Handy board help
|
|
You can build a stepper motor controller on a separate circuit board, then remove the motor control IC's off the handy board and use the output signals to control your stepper. Will have to write a program to run it. you will need a min of 4 outputs (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: PWM and encoder
|
|
The nonlinearity has to due with the characteristics of your motor. You will find that a single step of power at the low end has a greater effect on the speed than a single step at the high end, as the motor approaches its top speed. The (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Help!! Polaroid problem!!!
|
|
The reason you don't need a pull up resistor for the Handy Board is because the Handy Board has built in 47k pull up resistors on the digital inputs! -----Original Message----- From: MAR ERICSON <mar@cooper.edu> To: Darkman <lroska@cyberus.ca> Cc: (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | IC stack problem
|
|
Hello everybody, Is something wrong with this code or is it IC? { int a[4][4], i; for (i=0; i<4; i++) { a[i][i]=i; } } When I type this at the IC prompt it complains: Downloading 79 bytes (addresses C200-C24E): 79 loaded COMPILER ERROR!: 2 extra (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Help!! Polaroid problem!!!
|
|
well....I might be the way you are powering the sensors ??? Maybe luck ???? :)))))) Actually I don't why you don't need any of those supporting parts. A short question ...For what range are you using the sensors (are you using the binh signal) ?? We (...) (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Digitial input problem
|
|
Hi all, i have built a handyboard. It works fine. But on Digital PIN 9 "PAI" i got allways high level (1) during test via "hptest.c". I think i haven´t any soldering problems. That´s wrong ??? bernd klein (26 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
|
