 | | Are these codes proprietary
|
|
Hi: I was wonderig if the codes such as analog(), digital(), process() etc are proprietary. If not how can I see the C/assembly version of them. I need them to learn how Motorola 68hc11 assembly works and also I am a bit curious. Any help would be (...) (26 years ago, 14-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Are these codes proprietary
|
|
Hi: I was wonderig if the codes such as analog(), digital(), process() etc are proprietary. If not how can I see the C/assembly version of them. I need them to learn how Motorola 68hc11 assembly works and also I am a bit curious. Any help would be (...) (26 years ago, 14-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Are the codes proprietary
|
|
Hi: I was wonderig if the codes such as analog(), digital(), process() etc are proprietary. If not how can I see the C/assembly version of them. I need them to learn how Motorola 68hc11 assembly works and also I am a bit curious. Any help would be (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: re-download problem
|
|
Try turning off the board and holding down the start button while re-powering the board. Hope it works for you. Terry P. Gathright ---...--- (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: re-download problem
|
|
Hold down the START button while powering on. This will prevent the board from running main(). Fred In your message you said: (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo Routines
|
|
When I see the servo chatter, the knob is returning the same value. In fact I can just set a constant unchanging value without using the knob and get the chatter. I've tried this on two HB's and get the same results. The servos are small Futabas. (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo Routines
|
|
can you ascertain whether the knob is returning the same value every time through the loop? i wasn't clear if "even when the knob is not changing" meant just that you weren't turning the knob, or whether you were sure it was always producing the (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | re-download problem
|
|
I forgot to unload the program that I was running on my handyboard before I quit out of ic. and it won't let me putting the board on bootstrap mode. as soon as I power up the board, it starts running the last program. can anyone tell me how to clear (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Servo Routines
|
|
Question. I've been playin with the servo routines available from the HB page. One thing I've noticed. The servo's seem to chatter a lot. Is this normal. A routine that does nothing but loop, read the knob and output a value based on the knob to the (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Vector V2x Compass
|
|
Hi Armeen, I have the same problem as you. I thought my HB was faulty or it doesn't work with the 68hc11E processor I use or something. So what I did was: I wrote a very simple IC-Routine. You have to load this program with "load v2x.c" and call the (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
