 | | Re: 16 digital outputs as Fred suggested
|
|
1. please read the Appendix B documentation in (URL) explains this in more detail than the FAQ. 2. you must the even-numbered Yx signals for output latches. Since Y6 is taken (by the on-board latch for the motor drivers), you're left with Y0, Y2, (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Help - Cannot download!
|
|
try using DL.EXE (part of the Interactive C distribution) after following the serial port options directions given the FAQ (under downloading problems). fred In your message you said: (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Vector V2x Compass
|
|
Hello: I have a V2x compass and I was trying to hook it into my handyboard using Tom Brusehaver's .icb, .c and instructions as described in the contributed section. I have also grounded the M/S pin on the compass. The EOC pin is sent to the HB thru (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Analog Encoders
|
|
Hi, when I compile fencdr0.asm, I get "xxxjunk.c"(68): Warning --- Value Truncated "xxxjunk.c"(70): Warning --- Value Truncated "xxxjunk.c"(68): Warning --- Value Truncated "xxxjunk.c"(70): Warning --- Value Truncated Does everyone else get this (...) (26 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | >1A adapter?
|
|
Hello folks, I am currently using the HB to control a robot tethered to a PC (via the serial/charger board), as I'm using genetic algorithms to evolve controllers. The robot pulls about an amp (with motors, servo, sonar etc.), and I'm running it off (...) (26 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | RE: Multitasking (fwd)
|
|
I duno... I fergot. Sorry. :( It was a long time ago (milage-wise). I didn't use that method of mutitaking anymore and I didn't save the old code. But, I don't think so, I can't imagine that would be my style. I would set a global variable from (...) (26 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | 16 digital outputs as Fred suggested
|
|
Hi guys, I needed 16 digital outputs for my handyboard, so I put up a very simple expansion board the way Fred suggested in his handboard FAQ: I connected two more hc374 with their d-inputs to LCD-display's data bus (d0 - d7). Then I connected the (...) (26 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Rere: Smooth PWM in IC 3.1?
|
|
At 08:17 PM 4/11/98 -0600, I wrote: <snip> (...) <snip> Correction: You'll also need Julian's lib_hb.c to go with it. Again, rename your current version first so you don't overwrite it. Put the new one in the libs directory where the old one was, (...) (26 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Smooth PWM in IC 3.1?
|
|
(...) Yes, it is possible. It must be, 'cause I've been doing it. You simply need to download Julian's pcode_hb.s19 (rename your other one first) and put it in the IC31\libs directory (or whatever you call it). IC 3.1 ought to automatically load it (...) (26 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
|
| |
| | Re: SPI?
|
|
(...) this is correct... (...) but this is not. the Handy Board communicates with the desktop computer using the SCI: serial communications interface. The SPI is for high speed (up to 1 megabaud) sychronous (i.e., separate clock signal) transfer to (...) (26 years ago, 11-Apr-98, to lugnet.robotics.handyboard)
|
