To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.cad.dev.macOpen lugnet.cad.dev.mac in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 CAD / Development / Macintosh / *1056 (-10)
  Re: Bricksmith 2.4: Faster. Much Faster.
 
(...) One drawback with VBOs is that - unlike displaylists - you can't stick arbitrary GL calls in them. I'm using lists because I need to be able to put matrix operations in them as well as geometry. (...) Change the cull-face orientation ;-) (...) (...) (14 years ago, 16-Jun-10, to lugnet.cad.dev.mac, FTX)
 
  Re: Bricksmith 2.4: Faster. Much Faster.
 
In lugnet.cad.dev.mac, Allen Smith wrote: <snip> (...) Thanks for the insight Allen, I'm also not a 3D guru, but I like to fool around with it as much as anyone interested in 3d programming. Your method is roughly the same as what LD4DStdudio does, (...) (14 years ago, 16-Jun-10, to lugnet.cad.dev.mac, FTX)
 
  Re: Bricksmith 2.4: Faster. Much Faster.
 
(...) And another thing... The BFC technique actually has an advantage over conditional lines because it works on the entire scene after it's been assembled. Whereas the conditional lines at the edges of the primitives are created in advance, and (...) (14 years ago, 16-Jun-10, to lugnet.cad.dev.mac, lugnet.cad.dev, FTX)
 
  Re: Bricksmith 2.4: Faster. Much Faster.
 
(...) (URL) technique and the conditional lines both target the same edges lines where the front facing polygons meet the back facing polygons, so the results should be quite similar. (14 years ago, 16-Jun-10, to lugnet.cad.dev.mac, FTX)
 
  Re: Bricksmith 2.4: Faster. Much Faster.
 
(...) You can ignore the conditional lines and achieve the same effect with display lists using the stencil buffer techniques presented here: (URL) (14 years ago, 16-Jun-10, to lugnet.cad.dev.mac, FTX)
 
  Re: Bricksmith 2.4: Faster. Much Faster.
 
(...) Heh, you hit that problem too? I've played around writing an OpenGL LDraw renderer based exclusively on display lists, but I can't for the life of me figure out how to handle conditional lines in this setup. Has anyone else solved this (...) (14 years ago, 16-Jun-10, to lugnet.cad.dev.mac, FTX)
 
  Re: Bricksmith 2.4: Faster. Much Faster.
 
(...) Hi Roland, Bricksmith now recursively flattens the geometry for each referenced top-level part then sorts it according to primitive type (triangles, quads, lines). Since the primitives are sorted, each type can be enclosed in a single glBegin (...) (14 years ago, 16-Jun-10, to lugnet.cad.dev.mac, FTX)
 
  Re: Bricksmith 2.4: Faster. Much Faster.
 
In lugnet.cad.dev.mac, Kevin L. Clague wrote: <snip> (...) Hi Kevin, Sorry I replied to the wrong message, that's what you get if you read the group in a newsgroup client and post at the site. Still hoping Allan could share some insight on the (...) (14 years ago, 15-Jun-10, to lugnet.cad.dev.mac, FTX)
 
  Re: Bricksmith 2.4: Faster. Much Faster.
 
(...) Hi Roland, Just to be clear, Allan recoded and achieved this fantastic performance improvement. Kevin (14 years ago, 15-Jun-10, to lugnet.cad.dev.mac, FTX)
 
  Re: Bricksmith 2.4: Faster. Much Faster.
 
In lugnet.cad.dev.mac, Kevin L. Clague wrote: <snip> (...) <snip> (...) Hi, Keving Just from a technical interest, how did you achieve that boost? I'm in the midst of writing a new LDraw renderer myself, so I'm very interested in any possible (...) (14 years ago, 14-Jun-10, to lugnet.cad.dev.mac, FTX)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR