 | | Great Edmonton Train Show (GETS) this weekend
|
|
This weekend, Sept 18 & 19th The Great Edmonton Train Show is being held in Edmonton, Alberta, Canada. If you are in the neighborhood drop by and check out NALUG's display this year. The show is being held at the Mayfield Inn Trade Center, 16615-109 (...) (20 years ago, 13-Sep-04, to lugnet.trains, lugnet.org.ca.nalug, lugnet.loc.ca.ab, lugnet.announce)
|
| |
| | Re: Couplings for long overhang 4 wheeled vehicles
|
|
(...) Tim, I believe the practice with such systems is to cross the chains, which would reduce the sag on curves somewhat. (20 years ago, 13-Sep-04, to lugnet.trains)
|
| |
| | Re: Couplings for long overhang 4 wheeled vehicles
|
|
Mind you, having had a look at my prototype again, it seems it used a centre buffer and side chains, the problem with that of course, is that for Lego 'corners' the chains would have to be so long they would drag on the track! Tim (20 years ago, 12-Sep-04, to lugnet.trains)
|
| |
| | Re: Couplings for long overhang 4 wheeled vehicles
|
|
(...) I had considered the problem of relying on the friction of the axles/pegs. My thoughts were that the magnet to magnet join would actually be the weak link, although the coupling assembly might pull apart a little at a time with use. Presumably (...) (20 years ago, 12-Sep-04, to lugnet.trains)
|
| |
| | Re: Couplings for long overhang 4 wheeled vehicles
|
|
(...) That's right. The problem with that is you're relying on the strength of the axle and peg friction in order not to pull the couplings apart. With 12-wide stock there's some serious weight to pull! Also, your magnet holder is likely to rotate, (...) (20 years ago, 12-Sep-04, to lugnet.trains, FTX)
|
| |
| | Lego Train sets spotted in Historic Rail catalog
|
|
I get a catalog from Historic Rail (www.historicrail.com) They are a seller of railroad books, art, and memorabilia. They have in the past featured a small selection of HO scale (and other scale models). I just got their latest catalog and they (...) (20 years ago, 11-Sep-04, to lugnet.lego.direct, lugnet.market.shopping, lugnet.trains)
|
| |
| | Re: Couplings for long overhang 4 wheeled vehicles
|
|
(...) Nicely done, it looks realy authentic. (20 years ago, 11-Sep-04, to lugnet.trains, FTX)
|
| |
| | Re: Couplings for long overhang 4 wheeled vehicles
|
|
(...) Like this? (URL) It looks pretty simple an effective, you get just a little bit of movement on the coupling shoe pivot but not enough to cause jack-knifing. The problem from my point of view is that its too wide, I am looking for something (...) (20 years ago, 11-Sep-04, to lugnet.trains, FTX)
|
| |
| | Re: Couplings for long overhang 4 wheeled vehicles
|
|
(...) I have used various methods, including the magnet holder mentioned above, though the method below is the best one for long overhangs: Parts required: Two Technic plates 2x4 with holes (3709b). (URL) One K3 black elastic band, 18mm diameter, (...) (20 years ago, 9-Sep-04, to lugnet.trains, FTX)
|
| |
| | Re: Motorized Switch using Monkey Motor
|
|
(...) Hi Philippe, You're welcome & thanks! Perhaps Lenz decoders are more readily available where you live? They have some pretty small ones on their site here: (URL) The answer to your other question is "sort of". Most decoders have a DC (...) (20 years ago, 10-Sep-04, to lugnet.trains, FTX)
|
