 | | Re: 9V train collection completed
|
|
(...) come (...) Ben, are you SURE you have all the 9v sets after this deal? I mean ALL the real 9v sets plus ALL the fake ones? Jon (24 years ago, 18-May-00, to lugnet.trains)
|
| |
| | Re: 3225 Classic Train engine
|
|
(...) Hello Ryan. The 3225 Locomotive has generated a lot of derision on LUGNET but I actually like it partly beause it is Lego's only recent attempt at a steam engine. I think it is supposed to represent a typical European shunter (US=Switcher) (...) (24 years ago, 18-May-00, to lugnet.trains)
|
| |
| | Re: New to me- Ludo's trains
|
|
(...) Thanks for the interest. I'm thinking of redo the Belgian locomotive. Same color sheme but 1 brick less high. He can't pass under my bridge !! The model is created with MLCAD and the .dat file is available at my site. Now i'm working on the (...) (24 years ago, 18-May-00, to lugnet.trains)
|
| |
| | Re: New to me- Ludo's trains
|
|
Ludo's web site: (Sorry) (...) must (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | New to me- Ludo's trains
|
|
I do try to catch all the train stuff that comes through this group, but I must have missed your site, Ludo. So wonderful to see more train models, as I just a few days ago saw your web site again. I don't recall having seen the two locomotives (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
Hello, Ludo! Thanks VERY much for pioneering this operation for me. I have now fully repaired my 12v motorized track switch box. :-) Very happy it now works. I went home during lunch and soldered the thin coil wire back onto the inside plug (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
(...) Hi Folks! It was originally glued on four sides. After opening, i glued it back together with special ABS glue. I found this in a shop where they sell models (airplane, cars,..) Pictures says, in this case, more than words, isn't it? regards, (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Question about Running 12v trains
|
|
(...) One possible explanation for this (since I have washed many bricks and noticed this sometimes, but not most of the time): Dirty bricks will have a layer of grit on them which could throw off the tolerances, and will increase wear, especially (...) (24 years ago, 17-May-00, to lugnet.trains, lugnet.boats, lugnet.general)
|
| |
| | Re: Question about Running 12v trains
|
|
(...) first (...) 4.5V (...) At the age of maybe 5 to 7 I built a paddle steamer too, but I used the red swimming hulls of set 311: (URL) I built it with a gap in the middle for the paddles shaft and placed my 103 motor avove that. (I dared to use (...) (24 years ago, 17-May-00, to lugnet.trains, lugnet.boats)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
Thanks, James! I'll try to get this hooked up tonight. Melting the plastic is a concern. We'll see if I'm worthy. Thanks for the advice. later, James Mathis (...) to (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
(...) _small_ iron, using low melt solder, and lots of flux. I use a Antax 18W, 12V iron (but, it is british, so you are not likely to be able to get one). Otherwise, a Temp. Controlled iron, or run a small (25W) iron using a Variac (Variable (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
After a couple of hours, my 12volt points motor gray box is opened. I damaged the top cover slightly at its base along the flange at one corner. The damage is a flex/cut through the flange caused by too strong of a cut into the very small gap (...) (24 years ago, 17-May-00, to lugnet.trains)
|
| |
| | Re: Lego layout from the seventies
|
|
(...) See if you can?? You mean try NOT to spot any :-/ That's what got me about 1/2-1 hr with a Model Builder at the LLC Grand Opening weekend - my grousing about all the parts in pink, light blue, green, and brown that just weren't purchasable. I (...) (24 years ago, 17-May-00, to lugnet.general, lugnet.trains)
|
| |
| | Re: Question about Running 12v trains
|
|
(...) Ben, we have _got_ to hear the story of this! I used to make paddle "steamers", using Electical tape and Lego (the tape seals the Lego up quite well...except across the bottom...) I don't have any pic's here, and I doubt there are any at (...) (24 years ago, 16-May-00, to lugnet.trains, lugnet.boats)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
(...) At least the long sides, but I fear it have been all four sides.... Regards and good night (0:30 am) Ben (24 years ago, 16-May-00, to lugnet.trains)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
Thank you for the photograph of the opened gray motorized points box, Ben. What a task to open that box! Which sides of the gray box were glued together? - the long sides or the short sides? Thanks. later, James Mathis (...) (24 years ago, 16-May-00, to lugnet.trains)
|
| |
| | Re: Question about Running 12v trains
|
|
Thanks for the information, guys! Now, to justify the space that my layout may "require" to my wife. later, James Mathis (...) the (...) (24 years ago, 16-May-00, to lugnet.trains)
|
| |
| | Re: Help Open 12v switch track motor- doesn't switch
|
|
(...) Dear James (and whoever might be interested in this also), I took the point motor from Ludo and opened it again (was hardly glued now). And I took a few pictures to put the best of them on my homepage here: (URL) direct picture link here: (...) (24 years ago, 16-May-00, to lugnet.trains)
|
| |
| | Re: Question about Running 12v trains
|
|
(...) I just wanted to confirm: I totally agree with the opinion of James Powell. Light bricks might be shortened in their expected lifetime by to high voltage. With 9 V they shold last for a very long time. The Lego® motors (especially the older (...) (24 years ago, 16-May-00, to lugnet.trains)
|
| |
| | 3225 Classic Train engine
|
|
I recently acquired the 3225 Classic Train. My interest is rather new for trains both in real life and in LEGO so I have no idea how realistic this engine is. It seems odd to me that there is a lever at the front of the train. Would it be more (...) (24 years ago, 16-May-00, to lugnet.trains)
|
