 | | Re: SW-something switcher
|
|
(...) Hey Lar, maybe I'll have Rickey and his exact-o knife have a looksie at the problem;-) <inside GMLTC joke> -John (...) (23 years ago, 4-May-01, to lugnet.trains, lugnet.build)
|
| |
| | Re: SW-something switcher
|
|
(...) Rick Clark did a black and green Burlington Northern switcher (6-wide) tapering this way, and it looks great. Unfortunately, he doesn't have pics of it on his site. This is the best picture I could find on the PNLTC site: (URL) loco in (...) (23 years ago, 4-May-01, to lugnet.trains, lugnet.build)
|
| |
| | Re: SW-something switcher
|
|
(...) I suspect he used the dual taper piece (4x4x1 high) in the yellow and red/black show trucks... that is a perfect piece for this application, but the problem with it is that it tapers from 4 to 2... Talk about your strong argument for making (...) (23 years ago, 4-May-01, to lugnet.trains, lugnet.build)
|
| |
| | Re: SW-something switcher
|
|
(...) Yeah, that angle in is a bummer. Frankly, my solution has been to avoid it, because nothing is going to look just right given the limitations of the elements-- for *8wide*, that is. Rob Werner in the GFLTC has built a really nice switcher (...) (23 years ago, 4-May-01, to lugnet.trains, lugnet.build)
|
| |
| | Re: SW-something switcher
|
|
(...) Not from me... Seems like a tough problem as long as the slope on the hood remains above the hinge bricks, thus producing an "over-bite", as such. From the photos, I don't see much of a "gap", but perhaps a better angle would show it? Or, is (...) (23 years ago, 4-May-01, to lugnet.trains, lugnet.build)
|
| |
| | Re: SW-something switcher
|
|
(...) Looks good as it is, your addition of handrails on the rear of the cab is the first I've seen among SW-type builders. I believe that 8 wide is the best way to portray American railroad equipment.-Harvey (23 years ago, 4-May-01, to lugnet.trains, lugnet.build)
|
| |
| | SW-something switcher
|
|
Here is the most complete version of my SW series switcher... It started out as a SW1200 but I think I deviated from that design a bit. (URL) isn't the finished product yet but I am running into a problem. Just before the cab there is part of the (...) (23 years ago, 4-May-01, to lugnet.trains, lugnet.build)
|
| |
| | Re: Home layouts (Re: Huge layout)
|
|
(...) A simple examination of the electronics says that there is almost no possibility of a problem if the two controllers are set to the same polarity. (23 years ago, 4-May-01, to lugnet.trains)
|
| |
| | Re: Where to start
|
|
(...) ones, I know the sealed ones keep the tires soft longer, but... Also latly I'v found that some parts in the bulk brick tubs and other sets have had a blck film on them, then you get it on your hads and it travels around your parts. Josh (23 years ago, 4-May-01, to lugnet.lego.direct, lugnet.trains)
|
| |
| | Re: Home layouts (Re: Huge layout)
|
|
(...) I was in charge of powering the train for the 3000+' attempt at PNLTC's G2K World Record attempt. We used 10 or 12 power supplies on a single very long track. As long as the polarity is set right, we detected no ill effects. The train speed (...) (23 years ago, 3-May-01, to lugnet.trains)
|
