 | | Re: Need to figure out how to get this motor unit attached.
|
|
"Chris Orchard" <chris_orchard@+Remo...es.com.au> wrote in message news:Ixyn0n.230B@lugnet.com... (...) First up, something about the quotation style seems to be getting screwed up, I normally separate out different levels of quotation to mark them (...) (18 years ago, 19-Apr-06, to lugnet.technic)
|
| |
| | Re: Need to figure out how to get this motor unit attached.
|
|
(...) One-way can also be done with an gear on the pivot of an arm meshing with an idler gear on the end that swings between two close gears. You wouldn't have to go through any 90 deg twists then. :P (...) I could be wrong, but I thought that the (...) (18 years ago, 19-Apr-06, to lugnet.technic)
|
| |
| | Re: Need to figure out how to get this motor unit attached.
|
|
"Chris Orchard" <chris_orchard@+Remo...es.com.au> wrote in message news:Ixy4C6.CyI@lugnet.com... (...) The worm gear pics that I loaded into the folder recently are for a one-way worm gear drive. This basically is so I can set the hopper on and (...) (18 years ago, 19-Apr-06, to lugnet.technic)
|
| |
| | Re: Need to figure out how to get this motor unit attached.
|
|
(...) Hi Geoffrey, I think the easiest way to turn gearing through use of the worm gear, however as others will point out a worm gear is not very efficient gearing down mechanism, also if this is run for several hours at a time, the meshed gears (...) (18 years ago, 19-Apr-06, to lugnet.technic)
|
| |
| | Mindstorms.NET Request for Comments
|
|
I've been working with José David Parra on the next version of his (URL) RCX.NET> project, because 1.) the NXT system is coming out, and 2.) RCX.NET is basically a .NET wrapper of Spirit.ocx, which means it's not so nice to program with. Another (...) (18 years ago, 17-Apr-06, to lugnet.robotics, lugnet.technic, lugnet.announce, lugnet.robotics.rcx, lugnet.robotics.scout, FTX)
|
| |
| | Re: Request for info on the Control Lab Interface.
|
|
(...) Another question: Does this device work with serial port to USB adapters? I'd like to make this code as robust as possible, so this would be nice to know. If so, then I'd need to know if those adapters map themselves to the equivalent of COM1, (...) (18 years ago, 14-Apr-06, to lugnet.robotics, lugnet.technic, FTX)
|
| |
| | Need to figure out how to get this motor unit attached.
|
|
(URL) trying to figure out how to attach the new motor assembly and it's one-way drive train shown in pics 0-4 in this folder to the hopper assembly, at the point where the old assembly engaged the hopper itself, in pic 10 in the brickshelf folder (...) (18 years ago, 14-Apr-06, to lugnet.technic)
|
| |
| | Re: Request for info on the Control Lab Interface.
|
|
(...) Thanks for your information! I was also sent via email a very helpful page: (URL) His (URL) Research Page> has source code, which was also helpful. In fact, his ActiveX control might be useful for NQC. I had trouble getting it to connect to my (...) (18 years ago, 12-Apr-06, to lugnet.robotics, lugnet.technic, FTX)
|
| |
| | Re: Request for info on the Control Lab Interface.
|
|
(...) Yes, programs are executed on the PC. (...) Nothing is stored on the device. (...) It resides on the PC. (...) AFAIK, you will need a newer version of ROBOLAB. The older versions (forget which) did not support ControlLab. If you're up to the (...) (18 years ago, 11-Apr-06, to lugnet.robotics, lugnet.technic, FTX)
|
| |
| | Re: Help with converting voltage on circuit board
|
|
(...) Hi Danny, If we supply +12V to the top of the transistors, the drive circuit will most likely not be able to block those transistors completely (unless said drive circuit has an open collector structure with a pull up to the emitter of the (...) (18 years ago, 11-Apr-06, to lugnet.robotics, lugnet.technic)
|
