 | | Re: New crane MOC
|
|
(...) Woohoo!! Glad I decided to go to Portland!! Rest assured I'll get some pics ;) Hopefully I'll be around when you assemble it too - I can even help if you need it. (...) Nice work! Haven't seen a ringer here for quite a while. I agree with TJ, (...) (21 years ago, 4-Feb-04, to lugnet.technic)
|
| |
| | new Ferrari 1:10
|
|
(URL) from a message by Matteo Favalli: (URL) David (21 years ago, 3-Feb-04, to lugnet.technic)
|
| |
| | Re: automatic transmission
|
|
(...) I have never heard of this before... but I suppose you could do it with and RCX and two motors. think about it... if you had 2 inputs(the motors) into the transmission and 1 output with the RCX controlling which motor is in use and at what (...) (21 years ago, 3-Feb-04, to lugnet.technic)
|
| |
| | automatic transmission
|
|
I was out of ideas for what to do next, my "snow plow" or "snowblower" or whatever you like to call it, is finished and working, only need a truck or anything behind it to look cool. MLCad file will be avaiable soon... But today I was reading the (...) (21 years ago, 3-Feb-04, to lugnet.technic)
|
| |
| | Re: New crane MOC
|
|
(...) thanks tobbe. i will be sure to get lots of good pictures before it falls. i have seen the pictures of the TJ incident. bob Bob Kojima ko@fial.com (URL) Incorporated Telecom Monitoring Solutions 4343 SW Corbett Ave Portland, OR 97239 (...) (21 years ago, 3-Feb-04, to lugnet.technic)
|
| |
| | Re: New crane MOC
|
|
(...) thanks TJ. you are the crane master so a complement from you means a lot to me! i had to place a lot of orders for 1x5 liftarms thin to complete all the cross bracing. the red ones are hard to come by and the bricklink stores only have 1 or (...) (21 years ago, 3-Feb-04, to lugnet.technic)
|
| |
| | Re: Motion considerations when RCXing The Improved and New Old Miller Gustav's Post Mill
|
|
(...) gears and clutches for that. I've tried a crude version locking differential boxes together, and driving off the gears on the ends though. Okay, two ways to get a simple two-shaft concentric drive: The first is, as mentioned above, use a (...) (21 years ago, 3-Feb-04, to lugnet.castle, lugnet.technic, FTX)
|
| |
| | Re: Pneumatic Hoses
|
|
(...) I searched through previous posts and came across these: (URL) Versilic silicone tubing> (URL) Silicone fuel hose used for R/C airplanes> (URL) www.clippard.com> Also, McMaster-Carr is an excellent site for all sorts of things. Check out their (...) (21 years ago, 3-Feb-04, to lugnet.technic, FTX)
|
| |
| | Re: New crane MOC
|
|
(...) Hey now- crane disasters happen. You can't avoid it :-) (URL) Hopefully that won't scare Bob too badly :-) Let's just hope my streak of bad luck is over! -TJ (21 years ago, 3-Feb-04, to lugnet.technic, FTX)
|
| |
| | Re: Pneumatic Hoses
|
|
(...) No, not yet. You're right, this question comes up again and again. The best substitute I've used was some tubing that John Barnes indroduced me to. You may want to email him and ask for the brand name (barnes@SPAMBARFsensors.com). I'll look at (...) (21 years ago, 3-Feb-04, to lugnet.technic)
|
